вступ
Welcome to the instruction manual for your new phrozen Sonic Mighty 14K LCD Resin 3D Printer. This guide provides essential information for setting up, operating, maintaining, and troubleshooting your device to ensure optimal performance and longevity. The Sonic Mighty 14K is designed for high-detail resin 3D printing, featuring a 10.1" monochrome LCD with 16.8*24.8µm XY resolution and an 8.8*5.0*9.3 inch printing volume, ideal for models, miniatures, and action figures.
Figure 1: Phrozen Sonic Mighty 14K LCD Resin 3D Printer with a sampле друк.
Налаштування
Розпакування та початкове налаштування
Carefully remove all components from the packaging. The Phrozen Sonic Mighty 14K comes largely pre-assembled, minimizing setup time. Ensure all packing materials are removed from inside and outside the printer.
Figure 2: Phrozen Sonic Mighty Revo highlighting smart features.
The printer features enhanced airflow, a built-in heater, and auto-leveling capabilities for a streamlined user experience.
Figure 3: Performance enhancement features of the printer.
Калібрування осі Z
Accurate Z-axis calibration is crucial for successful prints. Follow these steps:
- Navigate to the Z-Axis Control menu on the printer's touchscreen.
- Select the Z-Axis Calibration option.
- Вийміть ємність зі смолою з принтера.
- Помістіть аркуш паперу формату А4 на РК-екран.
- Tap 'Next' on the screen to initiate the Z-axis descent. The build plate will slowly move down until it makes contact with the LCD.
- Once the build plate is in contact with the paper, gently hold the build plate down and tighten the four calibration screws on the side of the building plate using the H3 hex key. Увага: Over-loosening these screws may cause the plate to fall and damage the LCD.
- After tightening, pull on all four corners of the paper to ensure equal tension and friction. If the paper can be pulled away completely or is unmovable, adjust the Z-offset using the interface until proper tension and friction are retained.
- Tap 'Next' to confirm the calibration. The build plate will ascend to the top, completing the calibration process.
Video 1: Detailed guide on calibrating the Z-Axis for the Phrozen Mighty Revo 3D Printer.
Операційна
Resin Loading
Ensure the resin vat is clean and properly installed. Gently shake your resin bottle before pouring. Slowly pour the resin into the vat, being careful not to overfill. The vat has a maximum fill line indicator.
Початок друку
Once your model is sliced and saved to a USB drive, insert the USB drive into the printer's front USB port. On the touchscreen, navigate to the 'Print' menu, select your file, and tap 'Print' to begin. The printer will automatically start the printing process.
Monitoring Prints with Phrozen Go App
The Phrozen Sonic Mighty 14K can be monitored remotely using the Phrozen Go App. This allows you to check print progress, receive notifications, and even stop prints from your smartphone.
Figure 4: Monitor your print status and receive notifications via the Phrozen Go App.
Відео 2: Кінецьview of the Phrozen Sonic Mighty Revo 14K LCD Resin 3D Printer's features, including app connectivity and smart detection.
Технічне обслуговування
Генеральне прибирання
Regular cleaning is essential for maintaining print quality and extending the life of your printer. After each print, carefully remove any cured resin from the build plate and the resin vat using the provided plastic scraper. Clean the build plate with isopropyl alcohol (IPA).
LCD and FEP Film Care
The LCD screen and FEP film are critical components. Avoid touching the LCD screen directly with your hands. When cleaning, use a soft, lint-free cloth and IPA. Be extremely careful not to scratch or puncture the FEP film in the resin vat, as this can lead to resin leaks and damage to the LCD.
Усунення несправностей
Print Adhesion Issues
If prints are not adhering to the build plate, ensure the build plate is properly calibrated (refer to Z-Axis Calibration section). Lightly sanding the build plate surface with fine-grit sandpaper can improve adhesion. Also, ensure the resin temperature is within the recommended range (typically 20-30°C).
Smart Residue and Failure Detection
The Sonic Mighty 14K is equipped with smart detection systems to prevent print failures and damage. The printer can detect foreign objects between the build plate and the release film, stopping the print to prevent LCD damage. It also notifies you of potential failures by detecting abnormalities in peeling force during printing.
Технічні характеристики
| Особливість | Деталь |
|---|---|
| Бренд | заморожений |
| Модель | Mighty Revo 14K |
| Номер моделі товару | MITY14K000NA |
| Розміри продукту | 13.9 x 13.6 x 20 дюймів |
| Вага товару | 39.7 фунта |
| Роздільна здатність XY | 16.8 x 24.8µm |
| Обсяг друку | 8.8 x 5.0 x 9.3 дюймів |
| матеріал | метал |
| Сумісні пристрої | Smartphone (for app monitoring) |
Ключові характеристики
- Next-Gen 14K Resolution: Upgraded monochrome LCD for ultra-fine detail.
- Optimized for Large-Scale Miniatures: Print multiple high-detail components with consistent exposure.
- Revo Series Innovations: Enhanced airflow, quick calibration, and streamlined leveling.
- Versatile Resin Compatibility: Supports a wide range of 405nm UV resins.
- Eco & User Considerate: Designed for power efficiency and ease of maintenance.
Гарантія та підтримка
Your phrozen Sonic Mighty 14K LCD Resin 3D Printer comes with a standard manufacturer's warranty. For detailed warranty information, please refer to the documentation included with your product or visit the official phrozen website. For technical support, troubleshooting assistance, or inquiries regarding parts and service, please contact phrozen customer support through their official channels.
