Інструкція з експлуатації комбінованого сповіщувача диму та чадного газу First Alert SMICO100-AC

1. Вступ

This manual provides essential information for the installation, operation, and maintenance of your First Alert SMICO100-AC Combination Smoke and Carbon Monoxide Alarm. This device is designed to provide early warning of smoke and carbon monoxide presence in your home. It features interconnectivity for synchronized alarming and a battery backup for continuous protection during power outagес.

2. Ключові характеристики

• Технологія точного виявлення: Advanced sensing technology designed to reduce nuisance alarms from cooking while providing early warning of fire.
• Можливість взаємоз'єднання: When one alarm sounds, all compatible interconnected alarms will activate, ensuring widespread alert throughout your home.
• Hardwire with Battery Backup: Operates on household electrical current with a 9V battery backup for continued protection during power failures.
• Штекер швидкого підключення: Facilitates easy installation without the need for rewiring existing compatible setups.
• Кнопка тестування/вимкнення: Allows for convenient testing of alarm functions and silencing of nuisance alarms.

3. Монтаж

3.1 Заходи безпеки

• Turn off power to the circuit before installation.
• Installation must comply with all local electrical codes.
• Consult a licensed electrician if you are unsure about wiring procedures.

3.2 Монтаж

1. Remove the old alarm unit from its mounting bracket.
2. Attach the new mounting bracket (included) to the electrical box on the ceiling or wall. Ensure the bracket is securely fastened.
3. Connect the wiring harness: Black to Black (Line), White to White (Neutral), and Orange to Orange (Interconnect). If your existing wiring uses different colors for interconnect, refer to the alarm's specific wiring diagram.
4. Plug the wiring harness into the back of the SMICO100-AC alarm unit.
5. Insert the 9V battery into the battery compartment. Ensure the battery is properly seated.
6. Вирівняйте блок сигналізації з монтажним кронштейном і поверніть його за годинниковою стрілкою, доки він надійно не зафіксується.
7. Відновіть живлення ланцюга.

4. Інструкція з експлуатації

4.1 Початкове ввімкнення

Upon restoring power, the alarm will perform a self-test. A green LED indicator should illuminate, signifying normal operation. If the alarm chirps or sounds continuously, refer to the troubleshooting section.

4.2 Кнопка тестування/вимкнення

• Тестування: Press and hold the Test/Silence button for a few seconds. The alarm will sound a loud, pulsating alarm pattern (3 beeps for smoke, 4 beeps for CO). This confirms the electronic circuitry, horn, and battery are working. Test weekly.
• Вимкнення сторонніх сигналів тривоги: In case of a non-emergency alarm (e.g., from cooking smoke), press the Test/Silence button to temporarily silence the alarm for several minutes. The alarm will automatically reset after the silence period if smoke or CO levels return to normal.

4.3 світлодіодні індикатори

• Зелений світлодіод: Flashes once every 60 seconds, indicating the alarm is receiving AC power and operating correctly.
• Жовтий світлодіод: Indicates a fault or malfunction. Refer to the troubleshooting section.
• Червоний світлодіод: Flashes rapidly during an alarm event (smoke or CO detected).

5. Керівні принципи розміщення

For optimal protection, install combination smoke and carbon monoxide alarms on every level of your home, including basements, and inside every bedroom. Additionally, place alarms in hallways outside sleeping areas.

6. Технічне обслуговування

6.1 Регулярне тестування

Test your alarm weekly by pressing the Test/Silence button. This ensures the unit is functioning correctly.

6.2 Заміна батареї

Replace the 9V battery at least once a year, or immediately when the alarm chirps every minute (indicating a low battery). To replace, open the battery drawer, remove the old battery, insert a new 9V alkaline battery, and close the drawer.

6.3 Очищення

Clean your alarm monthly to remove dust and debris. Use a soft brush attachment on your vacuum cleaner to gently vacuum the alarm's vents. Do not use water, cleaners, or solvents.

6.4 Заміна агрегату

Alarms have a limited lifespan. Replace your First Alert SMICO100-AC alarm at least every 10 years from the date of manufacture. The manufacture date is printed on the back of the alarm.

7. Вирішення проблем

8. Технічні характеристики

9. Гарантія та підтримка

For warranty information, technical support, or to obtain a user's manual, please refer to the documentation included with your product or visit the official First Alert website. Regular maintenance and testing are crucial for the proper functioning of your alarm.