1. Вступ
This manual provides detailed instructions for the installation, setup, and operation of your ULTRALOQ Bolt Pro Z-Wave Smart Lock. Please read all instructions carefully before installation and use to ensure proper functionality and safety.
Image: ULTRALOQ Bolt Pro Z-Wave Smart Lock with included WiFi Bridge and smartphone app interface.
2. Пакувальний лист
Перед початком встановлення переконайтеся, що всі компоненти присутні:
- Зовнішня збірка
- Внутрішня збірка
- Внутрішня монтажна пластина
- Болт
- Ударна пластина
- Розпірка
- Screws (various types: A, B, C, D, E, F)
- 4 лужні батарейки типу АА (в комплекті)
- Викрутка
- Посібник користувача
- Свердло шаблон
- Скинути голку
- Датчик дверей
- Резервні ключі (2)
- Міст WiFi
3. Посібник із встановлення
Важливі примітки перед установкою:
- Встановіть і перевірте замок з відкритими дверима, щоб уникнути блокування.
- Read all instructions before contacting customer support.
- НЕ встановлюйте батареї до встановлення замка.
- Дотримуйтесь інструкцій у послідовному порядку.
3.1. Підготовка дверей
Verify your door dimensions for compatibility:
- Товщина дверей: 1 3/8" to 1 3/4" (35mm to 44mm). For thicker doors up to 2 1/4" (57mm), a thick door kit may be required.
- Face Bore Hole Diameter: 2 1/8" (54mm) or 1 1/2" (38mm).
- Назад: 2 3/8" (60mm) or 2 3/4" (70mm).
- Door Edge Bore Hole Diameter: 1 дюймів (25 мм).
Image: Door preparation and measurement guide.
3.2. Installing the Bolt and Strike
Adjust the bolt length if necessary. Ensure the 'UP' icon on the bolt faces upwards. Secure the deadbolt into the door edge using Screw C. Install the strike plate into the door frame using appropriate screws (A, B, or C depending on your frame).
Video: Detailed guide on installing the U-Bolt Pro Z-Wave, including bolt and strike plate installation.
3.3. Installing the Exterior Assembly
If your door has a 1 1/2" bore hole, remove the spacer from the exterior assembly. Keep the tailpiece horizontal and pass it through the middle hole of the deadbolt. Route the cable through the gap below the bolt.
3.4. Встановлення монтажної пластини
Pass the cable through the bottom hole of the mounting plate. Align the tailpiece with the middle hole. Secure the mounting plate to the exterior assembly using Screws D. Tighten screws evenly.
3.5. Installing the Interior Assembly
Remove the battery cover from the interior assembly. Connect the cable from the exterior assembly to the socket on the interior assembly, ensuring the small teeth face up. Align the tailpiece with the hole in the interior assembly. Rotate the knob to a vertical position (unlocked). Attach the interior assembly to the mounting plate using Screws E.
3.6. Testing the Deadbolt
Rotate the knob a few times to ensure the bolt extends and retracts smoothly. Close the door and test again. The bolt should match the strike plate in the door frame without resistance.
3.7. Installing the Batteries and Performing Door Handing
This is a crucial step for the lock's operation. First, rotate the knob to a horizontal position (locked), which will extend the bolt. Insert the four AA batteries. The red LED light will turn on, and you will hear a beep. Then, install the battery cover.
Image: Battery installation in the interior assembly.
3.8. Встановлення датчика дверей
The door sensor should be mounted as close as possible to the edge of your door frame and to the bottom of the extended deadbolt. You can install it using the included sticker or Screw F. Ensure it is firmly pressed against the door frame.
Video: Detailed guide on installing the U-Bolt Pro Z-Wave, including door sensor installation.
4. Налаштування
4.1. U-tec App Setup
Download the U-tec App from your smartphone's app store. Follow the on-screen prompts to allow Bluetooth and notification access. Log in to your existing U-tec account or create a new one. The app will detect nearby ULTRALOQ devices. Select your ULTRALOQ Bolt Pro Z-Wave to begin the setup process.
Video: Step-by-step guide for setting up the U-tec App with your ULTRALOQ device.
4.2. Adding Admin, User Codes, and Fingerprints
Follow the app's instructions to set up an Admin Code (4-8 digits). This code is required for managing other users and settings. You can then add User Codes and Fingerprints for regular access. The app will guide you through the process of enrolling fingerprints by placing your finger on the reader from different angles.
Video: Guide to setting up the lock in Standalone Mode, including adding codes and fingerprints.
4.3. Z-Wave Hub Connection
The ULTRALOQ Bolt Pro Z-Wave is compatible with Z-Wave Plus hubs such as Samsung SmartThings, Hubitat, and Ezlo (Vera). Ensure your Z-Wave hub is online and within communication range (100 feet) of the lock. Follow your hub's instructions to put it into pairing mode, then initiate pairing from the U-tec App. If your hub requires a QR code or 5-digit pin code, find it on the back of the battery cover of your smart lock.
Image: Z-Wave compatibility with various smart home hubs.
5. Інструкція з експлуатації
5.1. Unlocking with Fingerprint
Place your registered fingerprint on the fingerprint reader. The lock will unlock if the fingerprint is recognized.
Image: Unlocking the smart lock using fingerprint ID.
5.2. Unlocking with Code
Enter your 4-8 digit user code on the keypad, then press the ULTRALOQ button to unlock. To lock, press the ULTRALOQ button again.
Image: Unlocking the smart lock using a numerical code on the keypad.
5.3. Unlocking with Key
To use the backup keys, pull the front panel from the bottom, then from the top to open it. Insert the key and rotate to unlock, just like a traditional deadbolt.
Image: Unlocking the smart lock using a physical backup key.
5.4. Auto Lock and Auto Unlock
The smart lock automatically locks if your door closes (detected by the door sensor) and unlocks when you arrive at your door with your smartphone in your pocket (Auto Unlock feature via app). By default, the lock will auto-lock after 30 seconds if left unlocked. This setting can be configured in the U-tec App.
Image: Smart lock auto-locking feature.
6. Технічне обслуговування
6.1. Заміна батареї
The lock is powered by four AA alkaline batteries. The U-tec App will provide low battery notifications. To replace, remove the interior assembly cover, replace the old batteries with new ones, and reattach the cover.
Image: Battery compartment for four AA batteries.
6.2. MicroUSB for Backup Power
In case the batteries are completely drained, you can use an external battery pack connected via the MicroUSB port on the exterior assembly to temporarily power the lock and gain access.
Image: MicroUSB port for emergency backup power.
6.3. Водонепроникність IP65
The external smart lock is IP65 rated for dust and weather resistance, built to withstand temperatures from -22°F to 149°F (-30°C to 65°C).
Image: IP65 dust and waterproof rating details.
7. Вирішення проблем
7.1. Resetting Your ULTRALOQ
To delete all user data or resolve certain issues, you may need to reset your ULTRALOQ to factory default settings. Use the reset needle to press the reset button (located on the interior assembly) for 3 seconds until you hear one long beep and two short beeps. All user data will be erased, and the lock will return to its original out-of-the-box settings.
Video: Instructions on how to reset the ULTRALOQ smart lock.
7.2. Keypad/Fingerprint Not Working
If the keypad or fingerprint reader is not responding correctly, it might be due to a loose or disconnected wire. Remove the interior assembly cover and ensure all cables are securely connected. Refer to the video below for guidance on reconnecting wires.
Video: Guide to disconnecting and reconnecting the keypad wire.
8. Технічні характеристики
- Назва моделі: U-Bolt Pro Series
- Номер моделі товару: U-BOLT-PRO-ZWAVE-UB01
- матеріал: Цинк
- Розміри: 3 x 1.2 x 3 дюймів
- Вага товару: 3.1 фунта (1.41 кілограма)
- Тип замка: Біометричний, кодовий замок, засув, клавіатура
- Протокол підключення: Bluetooth, Z-Wave
- Метод контролю: Додаток, Remote
- Джерело живлення: 4 лужних батарейок типу АА (в комплекті)
- Сертифікація безпеки: ANSI Grade 1 Certified
- Стійкість до погодних умов: IP65 rated dust and weatherproof
- Робоча температура: Від -22°F до 149°F (від -30°C до 65°C)
9. Інформація про гарантію
ULTRALOQ provides a lifetime mechanical warranty and an 18-month electronic warranty for the Bolt Pro Z-Wave Smart Lock.
10. Підтримка
For more information or technical assistance, please visit the official ULTRALOQ webсайт або зверніться до служби підтримки клієнтів:
- Webсайт: www.u-tec.com
- підтримка: support.u-tec.com
