Uponor Thermal Actuator 230V NC M28 x 1.5 Instruction Manual

1. Продукт закінчивсяview

The Uponor Thermal Actuator (Model 1022244) is designed for precise control of valves in Uponor, Polytherm, and Wirsbo Vario B underfloor heating distributors. This actuator operates on 230V AC and features a Normally Closed (NC) function, meaning the valve is closed when no power is supplied and opens when power is applied.

Ключові особливості:

• функція: Normally Closed (NC) - valve closes without current.
• Номінальний випtage: 230 В змінного струму.
• Internal Thread: M28 x 1.5 for secure mounting.
• Індикатор: Integrated lift indicator for visual status confirmation.
• Підключення: Equipped with a 0.75 mm² x 1m connection cable.
• захист: Splash-proof design.

Figure 1: Uponor Thermal Actuator (Model 1022244). This image shows the blue housing and grey base of the actuator.

2. Інформація про безпеку

Please read all safety instructions carefully before installation and operation. Failure to follow these instructions may result in electric shock, fire, or property damage.

• Кваліфікований персонал: Installation and electrical connections must only be performed by qualified and authorized personnel.
• Відключення живлення: Завжди відключайте головне живлення перед будь-яким встановленням, технічним обслуговуванням або усуненням несправностей.
• томtage: Забезпечити подачу обtage matches the actuator's nominal voltage (230 В змінного струму).
• Середовище: Do not install in environments exceeding the specified operating temperature or humidity ranges.
• Модифікації: Do not modify the actuator or its components. Unauthorized modifications void the warranty and can be hazardous.

3. Встановлення та налаштування

This section provides instructions for the correct installation of the thermal actuator onto your underfloor heating manifold.

1. Вимкнення живлення: Ensure the main power supply to the underfloor heating system is completely disconnected at the circuit breaker.
2. Identify Valve: Locate the specific valve on the Uponor, Polytherm, or Wirsbo Vario B underfloor heating distributor where the actuator is to be installed.
3. Монтаж приводу: Carefully screw the thermal actuator onto the valve's M28 x 1.5 internal thread. Hand-tighten until secure. Do not overtighten.
4. Електричне підключення: Connect the 230V AC electrical cable from the actuator to the appropriate control terminal on your heating system's wiring center. Ensure connections are secure and comply with local electrical codes. The actuator functions as Normally Closed (NC), meaning it will open the valve when power is supplied.
5. Verify Indicator: After connection, the lift indicator on the actuator should be visible. Its position will change once power is applied and the actuator begins to operate.
6. Відновлення живлення: Once all connections are secure and verified, restore power to the heating system.

Figure 2: Diagram of the Uponor Thermal Actuator showing its connection cable. This illustrates the electrical connection point.

4. Операція

The Uponor Thermal Actuator operates based on the electrical signal it receives from the heating control system.

• Нормально замкнутий (НЗ): When no electrical current is supplied to the actuator, the valve remains closed, preventing water flow.
• Valve Opening: When the heating control system sends a 230V AC signal to the actuator, it begins to heat up internally. This causes a wax element to expand, slowly pushing the valve stem open. This process typically takes a few minutes.
• Valve Closing: When the electrical signal is removed, the actuator cools down, and the wax element contracts, allowing the valve to close.
• Lift Indicator: The transparent lift indicator on the side of the actuator provides a visual confirmation of the valve's status. When the valve is open, the indicator will be in a different position compared to when it is closed.

5. Технічне обслуговування

The Uponor Thermal Actuator is designed for long-term, maintenance-free operation. However, periodic visual inspections are recommended.

• Візуальний огляд: Periodically check the actuator for any signs of physical damage, loose connections, or leaks around the valve.
• Прибирання: If necessary, gently wipe the exterior of the actuator with a dry or slightly damp тканина. Не використовуйте абразивні засоби чи розчинники.
• Перевірка функції: Observe the lift indicator during heating cycles to ensure the actuator is opening and closing the valve as expected.

No internal maintenance or lubrication is required for this device.

6. Вирішення проблем

If you experience issues with your Uponor Thermal Actuator, consult the following troubleshooting guide:

If troubleshooting steps do not resolve the issue, contact a qualified technician or Uponor customer support.

7. Технічні характеристики

Detailed specifications for the Uponor Thermal Actuator (Model 1022244).

Figure 3: Dimensional drawing of the Uponor Thermal Actuator. This diagram provides key measurements for installation planning.

8. Гарантія та підтримка

For warranty information, technical support, or spare parts availability, please contact Uponor customer service or your local distributor. Keep your purchase receipt as proof of purchase.

Uponor GmbH Contact Information: