1. Вступ
This manual provides essential information for the installation, operation, and maintenance of the BANNER ENGINEERING S18AW3FF50 EZ-Beam S18 Series Photoelectric Sensor. This sensor is designed for reliable object detection in industrial environments, featuring a 50 mm range, 20-250VAC input, and SPST solid-state light operate output.
Figure 1: BANNER ENGINEERING S18AW3FF50 Photoelectric Sensor with coiled cable.
2. Налаштування та встановлення
Правильне встановлення є вирішальним для оптимальної продуктивності та безпеки. Уважно виконайте ці кроки.
2.1 Розпакування та перевірка
- Carefully remove the sensor from its packaging.
- Inspect the sensor for any visible damage that may have occurred during shipping.
- Перевірте наявність усіх компонентів, перелічених у пакувальній накладній.
2.2 Монтаж датчика
The S18AW3FF50 sensor is designed for easy mounting. Ensure the mounting surface is stable and free from excessive vibration.
- Select a mounting location that provides clear line-of-sight for the sensor's detection range (50 mm).
- Secure the sensor using appropriate mounting hardware (not included). The sensor features a threaded barrel for secure attachment.
- Ensure the sensor is oriented correctly for the intended detection application.
Малюнок 2: Сторона view of the S18AW3FF50 sensor, showing the threaded barrel and cable.
2.3 Електричні підключення
УВАГА: Disconnect all power before making electrical connections to prevent electric shock or damage to the equipment.
The S18AW3FF50 operates on 20-250VAC input and provides an SPST Solid-State Light Operate output. The sensor comes with a 2M (6.5FT) cable.
| Колір дроту | функція |
|---|---|
| Коричневий | AC Line (L1) |
| Синій | AC Neutral (L2) |
| чорний | Output (SPST Light Operate) |
Connect the sensor wires to the control circuit according to the provided wiring diagram and local electrical codes. Ensure all connections are secure.
Figure 3: S18AW3FF50 sensor showing the cable with exposed wires for electrical connection.
3. Операція
Once installed and wired, the S18AW3FF50 sensor is ready for operation.
3.1 Увімкнення
Apply power to the sensor (20-250VAC). The sensor will typically have an indicator LED (if present) to show power status and output state.
3.2 Принцип виявлення
The S18AW3FF50 is a photoelectric sensor operating in a fixed field mode. It emits a light beam and detects objects based on the reflection or interruption of this beam. The "Light Operate" output means the output will be active when light is received by the sensor (i.e., when an object is detected or not detected, depending on the specific fixed field configuration).
3.3 Дальність ходу та продуктивність
The sensor has a specified detection range of 50 mm. Ensure that objects to be detected fall within this range for reliable operation. Environmental factors such as dust, moisture, and ambient light can affect performance.
4. Технічне обслуговування
The S18AW3FF50 sensor is designed for low maintenance. Regular checks can ensure long-term reliable operation.
4.1 Очищення
- Periodically clean the sensor lens and housing to remove dust, dirt, or debris that may accumulate and interfere with detection.
- Use a soft, lint-free cloth and a mild cleaning solution if necessary. Avoid abrasive cleaners or solvents.
4.2 Перевірка кабелів та з'єднань
- Regularly inspect the sensor cable for any signs of wear, cuts, or damage.
- Check electrical connections to ensure they remain secure and free from corrosion.
5. Вирішення проблем
This section provides solutions to common issues encountered with the S18AW3FF50 sensor.
| проблема | Можлива причина | Рішення |
|---|---|---|
| Датчик не вмикається | No power supply; Incorrect wiring; Damaged sensor. | Verify power supply (20-250VAC); Check wiring against Table 1; Replace sensor if damaged. |
| Sensor not detecting objects | Object out of range (50 mm); Dirty lens; Misalignment; Ambient light interference. | Ensure object is within 50 mm range; Clean sensor lens; Realign sensor; Shield sensor from strong ambient light. |
| Періодичне виявлення | Vibration; Loose connections; Fluctuating power. | Secure sensor mounting; Check all electrical connections; Ensure stable power supply. |
6. Технічні характеристики
Key technical specifications for the BANNER ENGINEERING S18AW3FF50 Photoelectric Sensor.
- модель: S18AW3FF50
- Серія: EZ-Beam S18 Series
- Діапазон виявлення: 50 мм
- Вхідний об'ємtage: 20-250 В змінного струму
- Тип виводу: SPST Solid-State Light Operate
- Довжина кабелю: 2 м (6.5 футів)
- Тип датчика: Photoelectric, Fixed Field
- Виробник: BANNER ENGINEERING
- ASIN: B07RZTBRLS
- Дата першої доступності: 3 грудня 2021 р
7. Гарантія та підтримка
For warranty information and technical support, please contact BANNER ENGINEERING directly or refer to their official webсайт.
Політика повернення: The product may be subject to a return policy of 30 days for refund/replacement, as per the seller's terms.
Виробник: BANNER ENGINEERING
Щоб отримати додаткову допомогу, відвідайте BANNER ENGINEERING official webсайт.
