VOFONO Keyless Entry Remote Replacement Key Fob Instruction Manual

1. Більшеview

This manual provides instructions for the VOFONO Keyless Entry Remote Replacement Key Fob. This product is designed to replace your original key fob for compatible vehicles, offering remote lock, unlock, and panic functions. It requires professional key cutting and specific programming steps to function correctly with your vehicle.

2. Налаштування та програмування

2.1. Примітки щодо сумісності

• This key fob is compatible with Toyota Rav4 models from 2006-2010 and Scion XB models from 2008-2013.
• It is a replacement remote key for vehicles using a "4D67" chip.
• Важливо: If your original Toyota Rav4 key fob has a letter "G" stamped on the key blade, this replacement key fob will not work.
• This transmitter is designed for vehicles with a regular key ignition and does not support push-start button vehicles.

2.2. Key Cutting

The physical key blade of this replacement fob is uncut. For proper vehicle operation, the key blade must be cut by a qualified automotive locksmith or a Toyota dealership. Ensure the locksmith is experienced with transponder keys.

2.3. Remote Programming Instructions

The remote functions (lock, unlock, panic) of the key fob require programming to your vehicle. Follow these steps carefully:

1. Ensure the key is out of the ignition.
2. The driver's door must be open, all other doors closed, and the driver's door unlocked.
3. Have all key fobs you wish to program nearby.
4. Insert the key into the ignition (do NOT turn it), then pull the key out. Repeat this sequence: IN, OUT, IN, OUT.
5. Close the driver's door, then open it. Repeat this sequence: CLOSE, OPEN, CLOSE, OPEN.
6. Insert the key into the ignition, then pull it out: IN, OUT.
7. Close the driver's door, then open it. Repeat this sequence, ending with the door closed: CLOSE, OPEN, CLOSE, OPEN, CLOSE!
8. Insert the key into the ignition: IN!
9. Turn the key to the ON position (do not start the engine), then immediately back to OFF.
10. Pull the key OUT! The door locks will cycle (lock and unlock) to acknowledge that the vehicle is in programming mode.
11. Протягом 40 секунд: Press the LOCK and UNLOCK buttons on the remote simultaneously for 1.5 seconds.
12. Immediately after releasing the LOCK and UNLOCK buttons, press the LOCK button by itself and hold for 2 seconds.
13. Within 3 seconds, the door locks should cycle once (lock and then unlock) indicating successful programming. If the door locks cycle twice, repeat steps 11 and 12 as the remote was not accepted.
14. Repeat steps 11 and 12 for each additional new remote you wish to program.
15. To exit programming mode, open the driver's door.

3. Операція

Once programmed and the key blade is cut, your VOFONO key fob will provide the following functions:

• Кнопка блокування: Press once to lock all vehicle doors.
• Кнопка розблокування: Press once to unlock the driver's door, press twice to unlock all doors.
• Panic/Hold Button: Натисніть і утримуйте, щоб активувати сигналізацію автомобіля. Натисніть ще раз, щоб вимкнути її.
• Кнопка відкриття багажника: Press once to open the vehicle's trunk or liftgate (if equipped and supported by the vehicle).

4. Технічне обслуговування

• Заміна батареї: The key fob uses a standard coin cell battery. When the remote range decreases or buttons become unresponsive, replace the battery. Refer to Image 2.2 for guidance on opening the fob.
• Загальний догляд: Avoid exposing the key fob to extreme temperatures, moisture, or direct sunlight for prolonged periods. Do not drop the fob or subject it to strong impacts.

5. Вирішення проблем

• Пульт не працює після програмування: Ensure all programming steps were followed precisely, paying close attention to timing. If the door locks cycled twice during programming, it indicates a failure; repeat the programming steps. Check the battery.
• Key Blade Does Not Start Vehicle: This key fob contains a transponder chip that must be programmed to your vehicle's immobilizer system. This typically requires specialized equipment available at an automotive locksmith or dealership. A simple key cut will not enable the car to start if the chip is not programmed.
• Переривчаста функціональність: Check the key fob battery. Ensure there are no strong radio frequency interferences in the area.

6. Технічні характеристики

7. Підтримка

For any questions regarding the product or assistance with programming, please feel free to contact VOFONO customer support. Contact details can typically be found on the product packaging or the retailer's webсайт.