Torin Hydraulic Welded Bottle Jack 12 Ton (Model TH91204X) User Manual

1. Вступ

This manual provides essential information for the safe and effective operation and maintenance of your Torin Hydraulic Welded Bottle Jack, Model TH91204X. This hydraulic bottle jack is designed for residential and commercial use, offering a robust lifting capacity of 12 Ton (24,000 lbs.). Its welded construction ensures durability and dependability for various lifting tasks.

Ключові особливості:

• Lifting range of 8.94" to 17.99" for versatile applications.
• Adjustable screw top extension with a heat-treated screw for precise low pickup height adjustment and maximum lift.
• Serrated, heat-treated saddle for a large lifting area and secure grip.
• Wide, rugged base for enhanced stability and strength.
• Reinforced critical stress points for extended life beyond 5000 lifting cycles.

2. Інформація про безпеку

Always prioritize safety when operating hydraulic lifting equipment. Failure to follow these instructions may result in personal injury or property damage.

• Прочитайте інструкцію: Перед використанням ознайомтеся з усіма інструкціями з експлуатації та попередженнями.
• Номінальна місткість: Never exceed the jack's rated capacity of 12 tons (24,000 lbs.).
• Стабільна поверхня: Always use the jack on a hard, level surface. Soft or uneven surfaces can cause the jack to shift or tip.
• Центральне навантаження: Position the jack saddle directly under the load's lifting point. Off-center loads can cause instability.
• Support the Load: Once the load is lifted, immediately support it with appropriate jack stands. Do not rely solely on the hydraulic jack to hold the load.
• Очистити область: Ensure the area around the jack and load is clear of personnel and obstructions during lifting and lowering.
• Засоби індивідуального захисту: Одягайте відповідне захисне спорядження, таке як рукавички та засоби захисту очей.
• Огляньте перед використанням: Check the jack for any signs of damage, leaks, or wear before each use. Do not use a damaged jack.
• Уникайте модифікацій: Do not modify the jack or use it for purposes other than its intended design.

3. Особливості продукту

The Torin Hydraulic Welded Bottle Jack TH91204X incorporates several design elements for enhanced performance and safety:

• Adjustable Screw Top: Allows for fine-tuning of the lifting height to match various vehicle or load requirements.
• Serrated Saddle: Provides a secure contact point with the load, reducing the risk of slippage.
• Welded Construction: Ensures a reliable structure with consistent welds, minimizing the risk of oil leakage and enhancing overall durability.
• Safety Bypass Valve: Prevents over-extension of the hydraulic ram, protecting the jack from damage.

4. Налаштування

Before using the jack, ensure it is placed on a firm, level surface. The package includes the bottle jack and its pump handle. No assembly is required for the main jack unit, but the handle needs to be assembled for operation.

• Розпакувати: Remove the bottle jack and handle components from the packaging.
• Зібрати ручку: The pump handle typically consists of two interlocking pieces. Slide the smaller handle piece into the larger piece until it is securely connected.
• Первинна перевірка: Before first use, ensure the release valve is fully closed by turning it clockwise. Pump the handle a few times to ensure the ram extends smoothly. If the ram does not extend, check the hydraulic fluid level (refer to Maintenance section).

5. Інструкція з експлуатації

Follow these steps for safe and effective operation of your hydraulic bottle jack:

5.1. Підіймання вантажу

1. Підготуйте робочу зону: Ensure the vehicle or load is on a hard, level surface. Engage the parking brake if applicable and block wheels that are not being lifted.
2. Розташуйте Джек: Place the jack directly under the vehicle manufacturer's recommended lifting point. Ensure the saddle is centered on the lifting point.
3. Close Release Valve: Insert the slotted end of the pump handle into the release valve. Turn the handle clockwise until the valve is firmly closed. Do not overtighten.
4. Adjust Screw Top (if needed): If additional height is required to reach the lifting point, rotate the adjustable screw top counter-clockwise to extend it to the desired height.
5. Pump the Handle: Insert the pump handle into the handle socket. Pump the handle steadily to raise the jack. Continue pumping until the load reaches the desired height.
6. Закріплення вантажу: Immediately place appropriately rated jack stands under the load at the manufacturer's recommended support points. Slowly lower the load onto the jack stands (see 5.2. Lowering a Load).

5.2. Опускання вантажу

1. Трохи підняти: If the load is resting on jack stands, slightly raise the load with the hydraulic jack to clear the jack stands.
2. Зняти стійки Джека: Carefully remove the jack stands from under the load.
3. Open Release Valve: Firmly grasp the pump handle. Slowly turn the release valve counter-clockwise to gradually lower the load. Do not open the valve too quickly, as this can cause the load to drop rapidly.
4. Retract Ram: Once the load is fully lowered and all weight is removed from the jack, manually push down on the saddle to fully retract the piston.

6. Технічне обслуговування

Regular maintenance ensures the longevity and safe operation of your hydraulic bottle jack.

• Гідравлічна рідина: Check the hydraulic fluid level periodically. To do this, ensure the ram is fully retracted and the jack is on a level surface. Remove the oil filler plug and add high-quality hydraulic jack oil if needed, ensuring the fluid level is just below the filler hole. Do not overfill.
• Прибирання: Keep the jack clean and free of dirt, grease, and debris. Wipe down the ram and other moving parts after each use.
• Змащення: Lightly lubricate moving parts, such as the pump mechanism and pivot points, with general-purpose grease or oil.
• Зберігання: Store the jack in a clean, dry place with the ram fully retracted.
• Кровотеча повітря: If the jack's performance is inconsistent (e.g., spongy feel, incomplete lift), it may need to be bled. With the ram fully retracted and the release valve open, remove the oil filler plug. Pump the handle several times to expel any trapped air. Close the filler plug and release valve, then test the jack.

7. Вирішення проблем

Нижче наведено поширені проблеми та їх можливі рішення:

8. Технічні характеристики

9. Гарантія та підтримка

For warranty information, technical support, or to order replacement parts, please refer to the official documentation included with your product or visit the manufacturer's webсайт. Зберігайте чек про покупку як підтвердження покупки для гарантійних претензій.

Що в коробці:

• Пляшка Джек
• Ручки
• Посібник користувача (цей документ)