1. Продукт закінчивсяview
The Bside CCT01 Digital Coating Thickness Gauge is designed for non-destructive, fast, and precise measurement of coating thickness. It operates based on either the magnetic induction principle (F probe) or the eddy current principle (N probe), depending on the substrate material. This device is equipped with both internal F and N probes.
The F probe is suitable for measuring non-magnetic coatings such as aluminum, chrome, copper, zinc, paint, varnish, enamel, and rubber on iron or steel substrates. It is also applicable to alloyed and hardened magnetic steel, but not austenitic steel.
The N probe is used for insulating coatings like paint, anodizing, and ceramics on all non-ferrous metals (e.g., aluminum, copper, zinc die casting, brass) and on austenitic stainless steels.
Малюнок 1: Спереду view of the Bside CCT01 Digital Coating Thickness Gauge, showing the LCD display, control buttons, and the Bside CCT01 branding.
2. Ключові характеристики
- Дисплей: 128x128 dot matrix LCD with standard menu operations.
- Режими вимірювання: Supports both single and continuous measurement.
- Group Modes: Two group modes: Direct (DIR) and General (GEN). Readings in Direct mode are lost upon power off, while General mode stores up to 80 readings per group.
- Калібрування: Zero-point calibration and multi-point calibration (up to 4 points) for each group.
- Управління даними: Ability to recall, delete specified readings, or delete entire group readings.
- Статистика: Displays mean, minimum, maximum, and standard deviation of readings.
- Probe Modes: Auto, Magnetic (F), and Eddy Current (N) probe selection.
- Функція сигналізації: User-definable high or low limit alarms for each group.
- Управління живленням: Функція автоматичного вимкнення.
- Підключення: USB interface for data transmission to a computer.
- Індикатори: Low battery and error indications.
3. Налаштування
3.1 Встановлення батареї
- Знайдіть батарейний відсік на задній панелі пристрою.
- Using a small screwdriver, remove the screws securing the battery compartment cover.
- Insert two 1.5V AAA batteries, ensuring correct polarity as indicated inside the compartment.
- Replace the battery compartment cover and secure it with the screws.
малюнок 2: View of the battery compartment, showing the placement for two 1.5V AAA batteries.
Малюнок 3: Задня частина view of the device, displaying the battery compartment cover and a warning regarding battery disposal and recycling.
3.2 Увімкнення/вимкнення
- Щоб увімкнути, натисніть і утримуйте потужність кнопку.
- Пристрій автоматично вимкнеться після певного періоду бездіяльності, щоб заощадити заряд батареї.
4. Інструкція з експлуатації
4.1 Режими вимірювання
- Одиночний режим: For individual measurements. Press the probe onto the surface, read the value, then lift.
- Безперервний режим: For scanning a surface. Keep the probe on the surface and slide it to take multiple readings.
4.2 Group Modes
- Direct (DIR) Group: Readings are displayed but not stored in memory. Data is lost when the device powers off.
- General (GEN) Group: Readings are automatically stored. Up to 80 readings can be stored for each of the four general groups. Each group maintains individual statistics, alarm limits, and calibration settings.
4.3 Калібрування
Accurate measurements require proper calibration. The device supports zero-point and multi-point calibration.
- Калібрування нульової точки: Used to set the zero reference on an uncoated substrate.
- Multi-Point Calibration (up to 4 points): For enhanced accuracy across the measurement range, using calibration foils of known thickness.
Refer to the on-screen menu for detailed calibration steps.
4.4 Probe Modes
The device can automatically detect the substrate type or be manually set.
- Автоматичний режим: The gauge automatically selects between F (magnetic induction) and N (eddy current) probe principles.
- Magnetic Mode (F Probe): For non-magnetic coatings on ferrous substrates.
- Eddy Current Mode (N Probe): For insulating coatings on non-ferrous substrates.
Малюнок 4: Збільшений план view of the professional test probe at the bottom of the device, designed for accurate contact with the measurement surface.
4.5 Налаштування будильників
Users can set high and low alarm limits for each group. An alarm icon will be displayed on the LCD when a reading exceeds these limits.
4.6 Data Management and Statistics
Navigate through the menu to:
- Нагадаємо: View збережені показники.
- Видалити: Remove specific readings or clear an entire group.
- Browse Statistics: View calculated statistics including the number of readings, mean, minimum, maximum, and standard deviation for the current group.
5. Передача даних
The Bside CCT01 features a USB interface for transferring measurement data to a computer. This allows for further analysis and record-keeping.
Малюнок 5: Збільшений план view of the USB interface located on the side of the device, used for data transmission.
6. Технічне обслуговування
6.1 Заміна батареї
When the low battery indicator appears, replace the AAA batteries as described in Section 3.1. Always use fresh batteries for optimal performance.
6.2 Очищення
Wipe the device with a soft, dry cloth. Do not use abrasive cleaners or solvents. Keep the probe tip clean and free of debris for accurate readings.
6.3 Зберігання
Store the device in its original packaging or a protective case when not in use. Avoid extreme temperatures and high humidity. If storing for extended periods, remove the batteries to prevent leakage.
7. Вирішення проблем
- Індикація низького заряду батареї: If the low battery icon appears, replace the batteries immediately.
- Індикація помилки: If an error message is displayed, refer to the device's on-screen help or power cycle the device. If the issue persists, contact customer support.
- Неточні показання: Ensure the probe tip is clean, the device is properly calibrated, and the correct probe mode (F/N/Auto) is selected for the substrate.
8. Технічні характеристики
| Параметр | F Probe (Magnetic Induction) | N Probe (Eddy Currents) |
|---|---|---|
| Діапазон вимірювання | 0 to 1300um (0 to 51.2mils) | 0 to 1300um (0 to 51.2mils) |
| Точність | (3% + 2um) / (3% + 0.078mils) | (3% + 2um) / (3% + 0.078mils) |
| роздільна здатність | 0-999um (1um), 1000-1300um (0.01mm) 0-39.39mils (0.01mils), 39.4-51.2mils (0.1mils) | 0-999um (1um), 1000-1300um (0.01mm) 0-39.39mils (0.01mils), 39.4-51.2mils (0.1mils) |
| Калібрування | One-point to four-point calibration, zero-point calibration | |
| Data Groups | One direct group (readings not stored), Four general groups (readings stored automatically) | |
| Статистика | Number of readings, mean, minimum, maximum, standard deviation | |
| одиниці | um, mm, mils | |
| сигналізація | User-settable high/low alarm limits | |
| Minimum Curvature Radius (Convex) | 1.5 мм | |
| Minimum Curvature Radius (Concave) | 25 мм | |
| Minimum Measuring Area Diameter | 6 мм | |
| Minimum Substrate Thickness | 0.5 мм (0.02 дюйми) | 0.3 мм (0.012 дюйми) |
| Maximum Measuring Rate | Два показання в секунду | |
| Інтерфейс комп'ютера | USB | |
| Джерело живлення | Two 1.5V AAA batteries (not included) | |
| Операційне середовище | Temperature: 0 to 40°C (32 to 104°F); Humidity: 20% to 90% RH | |
| Середовище зберігання | Температура: від -20 до 70°C (від -4 до 158°F) | |
| Відповідність стандартам | ROHS, WEEE | |
| Розміри | 110 мм x 53 мм x 24 мм (4.33 дюйма x 2.09 дюйма x 0.94 дюйма) | |
| Матеріал корпусу | ABS | |
| вага | 92 г (3.24 унції) | |
9. Вміст упаковки
Стандартний пакет включає:
- Bside CCT01 Digital Coating Thickness Gauge
- USB кабель
- Калібрувальні фольги
- Substrate Plates (Ferrous and Non-Ferrous)
- Посібник користувача
Figure 6: The Bside CCT01 gauge shown with its included accessories, including calibration foils and a USB cable, on a car panel.
10. Гарантія та підтримка
Information regarding product warranty and customer support is typically provided with the purchase documentation or available on the manufacturer's official website. Please refer to those resources for details on warranty coverage, technical assistance, and service options.
