1. Вступ
This manual provides detailed instructions for the installation, operation, and maintenance of the HOBBYWING XRotor PRO 40A ESC (Dual Pack). This Electronic Speed Controller is designed for multi-rotor applications, offering precise throttle response and compatibility with various flight control systems. Please read this manual thoroughly before use to ensure proper functionality and safety.
2. Інформація про безпеку
Важливі застереження щодо безпеки:
- Always disconnect the battery before handling or performing maintenance on the ESC or motor.
- Ensure correct polarity when connecting the battery to avoid damage to the ESC and other components.
- Operate the ESC within its specified voltage and current limits (3-6S Lipo, 40A continuous / 60A peak).
- Keep the ESC away from water, moisture, and extreme temperatures.
- Mount the ESC in a location with adequate airflow to prevent overheating.
- Цей продукт не є іграшкою. Зберігати в недоступному для дітей місці.
3. Вміст упаковки
Перевірте наявність усіх предметів у вашій упаковці:
- HOBBYWING XRotor PRO 40A ESC (2 units)
- Інструкція з експлуатації (цей документ)
Image: HOBBYWING XRotor PRO 40A ESC (Dual Pack). This image shows the two ESC units with their pre-attached wires.
4. Налаштування та встановлення
Follow these steps for proper installation of the XRotor PRO 40A ESC:
- Монтаж: Securely mount the ESCs to your multi-rotor frame. Ensure adequate ventilation around each ESC to dissipate heat effectively. Use double-sided tape or zip ties as appropriate for your frame.
- Підключення двигуна: Connect the three motor wires from the ESC to the three wires of your brushless motor. The order of connection determines the motor's rotation direction. If the motor spins in the wrong direction, swap any two of the three motor wires.
- Підключення живлення: Connect the red (+) and black (-) power wires of the ESC to your flight battery's corresponding terminals. Ensure correct polarity. The ESC supports 3-6S LiPo batteries.
- Signal Cable Connection: Connect the throttle signal cable (usually a single white or yellow wire) from the ESC to the appropriate channel on your flight controller. The twisted-pair design of the throttle signal cable helps reduce signal interference.
- Initial Calibration (if required by flight controller): Refer to your flight controller's manual for ESC calibration procedures. The XRotor PRO 40A ESC is designed for excellent compatibility and often requires minimal setup.
5. Інструкція з експлуатації
The XRotor PRO 40A ESC is largely plug-and-play due to its pre-set configurations. However, understanding its operation is crucial for optimal performance.
- Реакція на газ: The special core program for multi-rotor controllers significantly improves throttle response, providing precise control for flight maneuvers.
- Сумісність: Optimized software ensures excellent compatibility with disc-type motors and various flight control systems. It supports signal frequencies up to 621Hz. Note that throttle signals over 500Hz are non-standard.
- Час: All settings except "Timing" are pre-set. Adjusting motor timing is typically done via the flight controller or a separate programming card if advanced customization is desired. Refer to your motor's specifications for optimal timing settings.
- DEO Function: The ESC includes a DEO (Driving Efficiency Optimization) function. This can be enabled or disabled, usually through a programming item if available, to further enhance efficiency and response.
6. Технічне обслуговування
Regular maintenance ensures the longevity and reliable performance of your ESCs:
- Огляд: Periodically inspect all wires and solder joints for signs of wear, fraying, or corrosion. Repair or replace damaged components immediately.
- Прибирання: Keep the ESCs clean and free from dust, dirt, and debris. Use a soft brush or compressed air for cleaning. Avoid using liquids.
- Управління теплом: Ensure the ESCs are not consistently overheating during operation. If they are, check for adequate airflow, proper motor/propeller combination, and correct timing settings.
- Зберігання: When not in use for extended periods, store the ESCs in a dry, cool environment, disconnected from the battery.
7. Вирішення проблем
If you encounter issues with your XRotor PRO 40A ESC, refer to the following common problems and solutions:
| проблема | Можлива причина | Рішення |
|---|---|---|
| Мотор не обертається або заїкається. | Incorrect motor wire connection, ESC not calibrated, faulty motor/ESC. | Check motor wire connections; swap two wires if motor spins wrong way. Perform ESC calibration. Test with a different motor/ESC if possible. |
| ESC gets excessively hot. | Insufficient airflow, overloaded motor, incorrect timing. | Ensure proper ventilation. Check motor/propeller combination for appropriate load. Adjust motor timing if programmable. |
| Intermittent power or signal loss. | Loose connections, damaged wires, signal interference. | Inspect all solder joints and connectors. Ensure signal cable is securely connected and away from power wires. |
| ESC не вмикається. | Battery not connected, incorrect battery polarity, faulty battery/ESC. | Verify battery connection and polarity. Test battery voltage. Check for visible damage on ESC. |
8. Технічні характеристики
| Особливість | Деталь |
|---|---|
| Модель | 30902042 |
| Безперервний струм | 40А |
| Піковий струм | 60А |
| Вхідний об'ємtage | 3-6S LiPo |
| Тип BEC | Немає BEC |
| Applicable Multicopter Class | 550/650 Class Quadcopter |
| Розміри | 5.25 x 3.5 x 2.25 дюймів (розміри продукту) |
| Вага товару | 5.6 унції |
| матеріал | Алюміній, Пластик |
| UPC | 088718514408 |
9. Гарантія та підтримка
For warranty information and technical support, please contact HOBBYWING North America directly. Details regarding specific warranty periods and conditions are typically provided with the product packaging or on the official HOBBYWING webсайт.
Виробник: Технології хобі
Контакти: Refer to the official HOBBYWING webсайт для отримання найактуальнішої контактної інформації та ресурсів служби підтримки.
