Alpine DAB+ Glass Antenna Instruction Manual

вступ

The Alpine DAB+ Glass Antenna (Model KAE-242DA) is an amplified screen antenna designed for use with Alpine DAB products. This antenna provides enhanced digital radio reception, ensuring clear audio quality. Its compact and transparent design allows for discreet installation on your vehicle's windscreen.

Інформація про безпеку

• Уважно прочитайте всі інструкції перед установкою та використанням.
• Ensure the vehicle's ignition is off and the battery is disconnected before beginning installation to prevent electrical shorts or damage.
• Не заважайте водієві view or interfere with airbag deployment when choosing an installation location.
• Handle the antenna and cables with care to avoid damage.
• Якщо ви не впевнені щодо будь-якого етапу процесу встановлення, зверніться до кваліфікованого фахівця.

Вміст упаковки

Перевірте наявність усіх елементів в упаковці:

• 1x Alpine DAB+ Glass Antenna (KAE-242DA)

Image: The Alpine DAB+ Glass Antenna, showing the main antenna film, the small amplifier unit, and the attached coaxial cable with its connector.

Налаштування та встановлення

The KAE-242DA antenna is designed for application on the windscreen, typically near the A-pillar, for optimal reception. Follow these steps for proper installation:

1. Виберіть місце розташування: Select a clean, flat area on the inside of your vehicle's windscreen, preferably on the passenger side near the A-pillar. Ensure the chosen spot does not obstruct your view або перешкоджати роботі будь-яких систем безпеки транспортного засобу.
2. Очистіть поверхню: Thoroughly clean the chosen area on the windscreen with an alcohol-based cleaner to remove any dirt, grease, or residue. Allow the surface to dry completely. A clean surface is crucial for proper adhesion.
3. Підготовка антени: Carefully peel the protective backing from the transparent adhesive section of the antenna film. Avoid touching the adhesive surface.
4. Apply the Antenna: Carefully align the antenna film to the cleaned windscreen area and press firmly from one end to the other to avoid air bubbles. Ensure full contact with the glass.
5. Connect Ground Wire (if applicable): The small black amplifier unit attached to the antenna has a short black adhesive strip. This strip must be securely attached to a clean, unpainted metal surface (ground point) on the vehicle's A-pillar or chassis. This provides the necessary ground connection for the ampліфірник.
6. Прокладання кабелю: Carefully route the coaxial cable from the antenna along the A-pillar trim and under the dashboard towards your Alpine DAB radio or mobile media station. Ensure the cable is not pinched or exposed to sharp edges.
7. Підключення до головного пристрою: Plug the antenna's coaxial connector into the designated DAB antenna input on your Alpine head unit.
8. Тест функціональності: Reconnect the vehicle battery and turn on your Alpine head unit. Select the DAB radio source and perform a station scan to confirm proper reception. Adjust antenna position slightly if reception is poor (if possible without re-adhering).

Інструкція з експлуатації

Once installed, the Alpine DAB+ Glass Antenna operates automatically with your compatible Alpine DAB radio or mobile media station. The antenna amplifies the digital radio signal, providing a stable and clear reception.

• Ensure your Alpine head unit is set to the DAB (Digital Audio Broadcasting) source.
• Perform a station scan on your head unit to find available DAB channels in your area. Refer to your Alpine head unit's manual for specific instructions on scanning for DAB stations.
• The antenna is designed to be always active when connected to a powered Alpine DAB unit.

Технічне обслуговування

The Alpine DAB+ Glass Antenna requires minimal maintenance. Follow these guidelines to ensure its longevity and optimal performance:

• Прибирання: If the antenna film or amplifier unit becomes dusty, gently wipe it with a soft, dry, or slightly damp тканина. Не використовуйте агресивні хімікати або абразивні засоби для чищення.
• Огляд: Periodically check the antenna's adhesion to the windscreen and the ground connection for any signs of loosening or damage.
• Цілісність кабелю: Ensure the coaxial cable remains securely routed and free from kinks, pinches, or cuts.

Усунення несправностей

If you experience issues with your Alpine DAB+ Glass Antenna, consider the following:

• No DAB Signal or Poor Reception:
  • Ensure the antenna cable is securely connected to your Alpine head unit.
  • Verify that the ground connection of the amplifier unit is firmly attached to a clean metal surface.
  • Check if you are in an area with DAB signal coverage. DAB signal strength can vary by location.
  • Perform a new station scan on your Alpine head unit.
  • Ensure no metallic objects or window tinting (especially metallic tints) are obstructing the antenna's reception area.
• Періодичний сигнал:
  • This could be due to weak signal areas or interference. Try moving the vehicle to a different location.
  • Check for loose connections at the antenna or head unit.
• Antenna Detaching from Windscreen:
  • Ensure the windscreen surface was thoroughly cleaned and dry before initial application.
  • Extreme temperature fluctuations can sometimes affect adhesion. Re-application with new adhesive may be necessary if the original adhesive fails.

If problems persist after trying these steps, contact Alpine customer support or a qualified service technician.

Технічні характеристики

Гарантія та підтримка

For warranty information and technical support regarding your Alpine DAB+ Glass Antenna, please refer to the warranty card included with your product or visit the official Alpine Electronics website. You can also contact Alpine customer service directly for assistance with product inquiries, troubleshooting, or service needs.

Зберігайте докази покупки для гарантійних претензій.