вступ
This manual provides detailed instructions for the proper installation, operation, and maintenance of your CURT 17422 Short Trunnion Bar Weight Distribution Hitch with Sway Control. This specialized towing system is designed to enhance vehicle and trailer control by distributing the trailer's tongue weight more evenly across the vehicle's and trailer's axles, promoting a level towing experience. It is suitable for travel trailers, campers, and other large loads, with a gross trailer weight capacity up to 15,000 lbs. and a tongue weight capacity of 1,500 lbs.
The integrated sway control unit further assists in limiting lateral trailer movement, contributing to a more stable towing experience. Please read this manual thoroughly before installation and use to ensure safe and effective operation.
Важлива інформація з безпеки
УВАГА: Failure to read and follow these instructions can result in serious injury, death, or property damage. Always observe all safety precautions.
- Always ensure the weight distribution hitch is correctly installed and adjusted according to these instructions.
- Never exceed the lowest weight capacity of any towing component (vehicle, hitch, or trailer).
- Regularly inspect all components of the hitch system for wear, damage, or corrosion before each use.
- Ensure all fasteners are tightened to the specified torque values.
- Maintain proper tire pressure on both the tow vehicle and trailer.
- Drive at reduced speeds and exercise caution, especially in adverse weather conditions or when encountering crosswinds.
- Avoid sudden maneuvers, braking, or acceleration when towing.
- Always use safety chains between the tow vehicle and trailer.
- Be aware of Proposition 65 warnings regarding potential chemical exposure.
Вміст упаковки
Verify that all components listed below are present in your package. If any parts are missing or damaged, contact CURT customer support immediately.
- Weight Distribution Head Assembly
- 2-inch Shank
- 2-5/16-inch Trailer Ball (pre-torqued)
- Trunnion-style Spring Bars (2)
- Hook-up Brackets (2)
- Spring Bar Safety Chains (2)
- Sway Control Unit
- Sway Control Trailer Ball and Hitch Ball Attachment
- Reinforcement Plate and Attachment Clips for Sway Control
- All necessary fasteners (bolts, nuts, washers, pins, clips)
малюнок 1: Complete CURT 17422 Weight Distribution Hitch with Sway Control components.
малюнок 2: Included hardware for the CURT 17422 Weight Distribution Hitch.
Налаштування та встановлення
Proper installation is crucial for the safe and effective operation of your weight distribution hitch. It is recommended that installation be performed by a qualified technician if you are unfamiliar with towing equipment.
Необхідні інструменти:
- Динамометричний ключ
- Sockets and Wrenches (various sizes)
- Мірна стрічка
- Рівень
- Grease Gun (for lubrication)
Кроки встановлення:
- Підготовка транспортного засобу та причепа: Park the tow vehicle and trailer on a level surface. Ensure the trailer is loaded as it would be for travel. Level the trailer using its tongue jack. Measure and record the height of the front and rear bumper of the tow vehicle, and the height of the trailer coupler.
- Install Shank: Insert the 2-inch shank into your vehicle's receiver hitch. The shank can be flipped to provide the necessary drop or rise to achieve a level trailer. Secure with a hitch pin and clip.
- Attach Head Assembly: Slide the weight distribution head assembly onto the shank. The head features a pre-torqued 2-5/16-inch trailer ball. Adjust the tilt of the head to allow for proper spring bar tension.
- Встановлення пружинних стійок: Insert the trunnion-style spring bars into the head assembly. Ensure they are fully seated and secured with the retaining pins.
- Mount Hook-up Brackets: Position the hook-up brackets on the trailer frame, typically 28-32 inches back from the center of the coupler. Secure them firmly.
- Connect Spring Bar Chains: Attach the spring bar safety chains to the ends of the spring bars and then to the hook-up brackets. Use the lift handle to raise the spring bars and engage the chains onto the brackets, ensuring the trailer is level and the vehicle's front and rear bumper heights are restored to their original measurements (or slightly lower at the rear). Adjust chain links as needed to achieve proper tension.
- Install Sway Control Unit: Mount the sway control unit to the trailer frame and the hitch head using the provided hardware. Ensure the unit is positioned to allow full articulation without interference. The spacer plate helps ensure proper alignment.
- Остаточна перевірка: Double-check all connections, bolts, and pins. Ensure the trailer is level and the tow vehicle's suspension is properly loaded.
малюнок 3: The 2-inch shank can be adjusted for proper height.
малюнок 4: The hitch head can be adjusted for precise leveling.
малюнок 5: Forged steel trunnion-style spring bars provide load distribution.
малюнок 6: Snap-up brackets facilitate connecting the spring bar chains.
малюнок 7: Spacer plate for correct sway control ball alignment.
Інструкція з експлуатації
Connecting the Trailer:
- Ensure the tow vehicle and trailer are on level ground.
- Back the tow vehicle to align the hitch ball with the trailer coupler.
- Lower the trailer coupler onto the hitch ball and secure the coupler latch.
- Connect the safety chains and trailer wiring.
- Attach the spring bars to the head assembly and use the lift handle to engage the chains onto the hook-up brackets, ensuring proper tension for weight distribution.
- Connect the sway control unit as per installation instructions.
- Raise the trailer tongue jack fully and retract it.
малюнок 8: Illustration of how weight distribution levels the tow vehicle and trailer.
малюнок 9: Illustration of how sway control helps limit lateral trailer movement.
Disconnecting the Trailer:
- Park the tow vehicle and trailer on a level surface.
- Engage the parking brake on the tow vehicle.
- Disconnect the sway control unit.
- Using the lift handle, disengage the spring bar chains from the hook-up brackets.
- Remove the spring bars from the head assembly.
- Raise the trailer tongue jack to lift the coupler off the hitch ball.
- Disconnect safety chains and trailer wiring.
- Відсуньте евакуатор подалі від причепа.
Технічне обслуговування
Regular maintenance ensures the longevity and safe operation of your CURT weight distribution hitch.
- Перед кожною поїздкою: Inspect all bolts, pins, and connections for tightness and security. Check spring bars for any signs of bending or cracking. Ensure the hitch ball is securely torqued.
- Змащення: Periodically lubricate the hitch ball, spring bar pivot points, and the sway control unit's friction surfaces as recommended by the manufacturer. Use appropriate grease.
- Прибирання: Clean the hitch components regularly, especially after exposure to dirt, salt, or harsh weather. The durable black powder coat finish helps protect against corrosion, but regular cleaning will extend its life.
- Зберігання: When not in use, store the hitch components in a dry, protected area to prevent rust and damage.
Усунення несправностей
| проблема | Можлива причина | Рішення |
|---|---|---|
| Trailer not level / Vehicle sagging | Insufficient spring bar tension; incorrect head tilt; overloaded trailer. | Increase spring bar tension by adjusting chain links; adjust head tilt; ensure trailer is not overloaded. |
| Excessive trailer sway | Sway control not engaged; improper weight distribution; incorrect tire pressure; excessive speed. | Ensure sway control is properly connected and adjusted; verify weight distribution settings; check tire pressures; reduce towing speed. |
| Noisy operation (e.g., creaking, groaning) | Lack of lubrication on pivot points or sway control friction surfaces; loose components. | Lubricate hitch ball, spring bar pivot points, and sway control unit; inspect and tighten all fasteners. |
| Difficulty engaging/disengaging spring bars | Too much tension; vehicle/trailer not level. | Use the trailer tongue jack to raise the trailer coupler slightly, relieving tension on the spring bars before engaging/disengaging. |
Технічні характеристики
| Особливість | Деталь |
|---|---|
| Номер моделі | 17422 |
| Gross Trailer Weight (GTW) Capacity | До 15,000 фунтів. |
| Tongue Weight (TW) Capacity | Від 1,000 до 1,500 фунтів. |
| Розмір хвостовика | 2 x 2 дюйма |
| Trailer Ball Size | 2-5/16-inch (pre-torqued) |
| Spring Bar Length | 28-3/8 дюйма |
| матеріал | Alloy Steel, Forged Steel (spring bars) |
| Закінчити | Carbide Black Powder Coat |
| Вага товару | 107.8 фунта |
| Розміри продукту | 33 x 12 x 10.5 дюймів |
малюнок 10: Approximate dimensions of the CURT 17422 Weight Distribution Hitch components.
Інформація про гарантію
CURT Manufacturing provides a limited warranty for its products. Specific warranty terms and conditions, including coverage duration and claim procedures, are subject to change and may vary by product. Please refer to the official CURT website or the warranty card included with your product for the most current and detailed warranty information.
Примітка: Зберігайте чек про покупку для будь-яких гарантійних претензій.
Підтримка клієнтів
For technical assistance, missing parts, or warranty inquiries, please contact CURT customer support:
- Webсайт: Відвідайте чиновника CURT Manufacturing webсайт для отримання розділів поширених запитань, реєстрації продукту та варіантів зв’язку.
- телефон: Refer to the contact information provided on the CURT webсайт або упаковка продукту.
Звертаючись до служби підтримки, будь ласка, підготуйте номер моделі вашого продукту (17422) та підтвердження покупки.
