Інструкція з експлуатації захисних накладок TE Connectivity QC210AC

1. Вступ

1.1 продукт закінченоview

The TE Connectivity QC210AC is a protective label cover designed to shield and preserve labels in various environments. Constructed from durable, transparent vinyl, these covers ensure the legibility and longevity of underlying labels.

• матеріал: Вініл
• Прозорість: Transparent for clear visibility of labels
• Розміри: Approximately 50.8mm width
• функція: Provides a protective layer over existing labels

1.2 Використання за призначенням

These protective label covers are intended for use in industrial, electrical, and general applications where labels require protection from abrasion, moisture, dirt, and other environmental factors. They are suitable for safeguarding identification labels, warning labels, and instructional labels.

2. Налаштування та підготовка

2.1 Необхідні матеріали

• TE Connectivity QC210AC Protective Label Covers
• Labels to be protected
• Чиста тканина без ворсу
• Mild cleaning solution (e.g., isopropyl alcohol) if necessary

2.2 Підготовка поверхні

Before applying the protective cover, ensure the surface of the label and the surrounding area are clean, dry, and free from dust, oil, grease, or any other contaminants. Use a clean, lint-free cloth and a mild cleaning solution if needed, allowing the surface to dry completely before application.

3. Інструкція із застосування

Follow these steps for proper application of the QC210AC protective label cover:

1. Prepare the Label: Ensure the label you intend to cover is securely affixed and the surface is clean and dry as per Section 2.2.
2. Peel Backing: Carefully peel a small section of the release liner from one end of the QC210AC protective cover, exposing the adhesive side. Avoid touching the adhesive.
3. Вирівняти та застосувати: Align the exposed adhesive edge of the protective cover precisely over one edge of the label. Once aligned, slowly and steadily press the cover down, gradually peeling off the remaining release liner while smoothing the cover over the label.
4. Згладжування: Use your fingers or a soft, flat tool (e.g., a squeegee) to gently smooth out any air bubbles from the center outwards. Ensure firm contact across the entire surface of the label for optimal adhesion and protection.

малюнок 1: Illustration demonstrating the application of the protective label cover over an existing label. The image shows a transparent rectangular cover with one corner slightly lifted, revealing the instruction 'APPLY OVER LABEL' printed on its surface, indicating its intended use.

4. Догляд і технічне обслуговування

The QC210AC protective label covers are designed for durability. To maintain their clarity and protective qualities:

• Прибирання: If the cover becomes dirty, gently wipe it with a clean, soft, damp cloth. A mild soap solution can be used for stubborn dirt, followed by wiping with a clean, damp тканиною, щоб видалити будь-які залишки.
• Уникайте агресивних хімікатів: Do not use abrasive cleaners, solvents, or harsh chemicals, as these can damage the vinyl material and affect its transparency or adhesive properties.
• Огляд: Periodically inspect the covers for any signs of damage or peeling. Replace damaged covers to ensure continued protection of the underlying label.

5. Вирішення проблем

This section addresses common issues that may arise during or after application.

• Issue: Air Bubbles Under the Cover
  рішення: During application, ensure you smooth the cover from one end to the other, gradually removing the release liner. If bubbles appear, gently lift the edge of the cover closest to the bubble and re-apply, smoothing it down firmly. A soft squeegee can help.
• Issue: Poor Adhesion
  рішення: Ensure the label surface was thoroughly cleaned and dried before application. Contaminants like dust, oil, or moisture can prevent proper adhesion. Re-clean the surface if possible, or use a new cover if the adhesive has been compromised.
• Issue: Cover Peeling at Edges
  рішення: This can occur if the edges were not pressed down firmly during application or if the surface was not clean. Ensure all edges are pressed down securely. In environments with high traffic or abrasion, consider applying additional pressure to the edges during initial application.

6. Технічні характеристики

7. Гарантія та підтримка

For specific warranty information or technical support regarding the TE Connectivity QC210AC Protective Label Covers, please contact TE Connectivity directly through their official website or customer service channels. Ensure you have your product model number (QC210AC) available when seeking support.