Tascam US-144MKII USB Audio Interface User Manual

вступ

This manual provides essential information for the proper setup, operation, and maintenance of your Tascam US-144MKII USB Audio Interface. The US-144MKII is a compact, bus-powered USB 2.0 audio/MIDI interface designed for high-quality recording on Mac and Windows computers. It offers two microphone inputs with phantom power, two line inputs, a switchable guitar input, MIDI I/O, and S/PDIF digital audio I/O, supporting up to 96kHz/24-bit audio resolution.

Будь ласка, уважно прочитайте цей посібник перед використанням пристрою, щоб забезпечити безпечну та оптимальну роботу.

Інформація про безпеку

Always observe the following safety precautions to prevent electric shock, short circuit, damages, fire, or other hazards.

• Do not open the unit or attempt to disassemble the internal parts or modify them in any way.
• Не піддавайте пристрій дощу, використовуйте його поблизу води або в damp або вологих умов, або поставте на нього контейнери з рідинами, які можуть вилитися в будь-які отвори.
• If the USB cable becomes frayed or damaged, or if the unit is dropped or damaged, disconnect the USB cable immediately and have the unit inspected by qualified service personnel.
• Do not place the unit in a location where it may be exposed to excessive dust, vibrations, extreme cold or heat, or direct sunlight.
• Забезпечте належну вентиляцію навколо пристрою під час роботи.

Вміст упаковки

Переконайтеся, що ваш пакет містить такі елементи:

• Tascam US-144MKII USB Audio Interface unit
• USB-кабель 2.0
• Installation CD (for drivers and bundled software like Steinberg Cubase LE4)
• Посібник користувача (цей документ)

Продукт закінченийview

Передня панель

The front panel of the US-144MKII features all primary controls and input jacks for easy access during recording and monitoring.

• Регулятор INPUT: Adjusts the input gain for the microphone and line inputs.
• MON MIX Knob: Blends the direct input signal with the computer playback signal for zero-latency monitoring.
• LINE OUT Knob: Controls the output level to your studio monitors.
• Ручка PHONES: Adjusts the headphone output level.
• MONO Switch: Sums the stereo input signal to mono for monitoring.
• MIC/LINE Inputs (L/R): Комбіновані роз'єми XLR/TRS для підключення мікрофонів або лінійних інструментів.
• PHANTOM Power Switch: Активує фантомне живлення +48 В для конденсаторних мікрофонів.
• SIG/OL Indicators: Lights green when a signal is present, red when the input is overloading.
• LINE/GUITAR IN (R): 1/4-inch input for line-level or high-impedance guitar/bass signals.

Задня панель

The rear panel provides various connectivity options for your studio setup.

• LINE OUT (L/R): RCA outputs for connecting to powered studio monitors or an ampліфірник.
• MIDI-вхід/вихід: 5-pin DIN connectors for connecting MIDI devices such as keyboards or drum machines.
• DIGITAL IN/OUT (S/PDIF): Coaxial RCA connectors for digital audio input and output.
• Порт USB: Connects the interface to your computer for data transfer and power.

Налаштування

Установка драйвера

Before connecting the US-144MKII to your computer, it is crucial to install the latest drivers. The included CD may contain outdated drivers. For optimal performance and compatibility, always download the most current drivers directly from the official Tascam website. This ensures proper functionality and avoids potential issues, especially with newer operating systems.

1. Visit the official Tascam support webсайт.
2. Locate the support page for the US-144MKII.
3. Завантажте відповідний драйвер для вашої операційної системи (Windows або macOS).
4. Follow the on-screen instructions to install the driver. Do not connect the US-144MKII until prompted by the installer, or until the installation is complete.

Підключення інтерфейсу

1. Connect the US-144MKII to your computer using the supplied USB 2.0 cable. The unit is bus-powered, so no external power adapter is required.
2. Підключіть мікрофони до MIC/LINE Inputs (L/R) using XLR cables. If using condenser microphones, ensure the PHANTOM Power перемикач увімкнено.
3. Connect line-level instruments (e.g., synthesizers) to the MIC/LINE Inputs (L/R) using 1/4-inch TRS cables, or a guitar/bass to the LINE/GUITAR IN (R).
4. Підключіть свої студійні монітори до ЛІНІЙНИЙ ВИХІД (Л/П) Гнізда RCA.
5. Connect headphones to the 1/4-inch headphone jack on the front panel.
6. If using MIDI devices, connect them to the MIDI IN / OUT порти.

Операційна

Basic Recording Workflow

1. Увімкнення: Connect the US-144MKII to your computer via USB. The unit will power on automatically.
2. Налаштування програмного забезпечення: Open your Digital Audio Workstation (DAW) software (e.g., Cubase LE4, included). Go to the audio settings/preferences and select the Tascam US-144MKII as your audio input and output device.
3. Регулювання вхідного посилення: Connect your microphone or instrument. Speak into the microphone or play your instrument at the loudest expected level. Adjust the ВХІД ручку, поки не буде SIG/OL indicator lights green consistently, only occasionally flashing red on peaks. Avoid constant red illumination, which indicates clipping.
4. Моніторинг:
   • For zero-latency monitoring, adjust the MON MIX knob. Turning it towards "INPUT" increases the direct signal from your microphone/instrument, while turning it towards "COMPUTER" increases the playback from your DAW. Find a balance that allows you to hear both clearly without delay.
   • Adjust your headphone volume using the ТЕЛЕФОНИ knob and monitor speaker volume using the ЛІНІЙНИЙ ВИХІД ручка.
5. Запис: Create a new audio track in your DAW, select the appropriate input (e.g., Input 1 for Mic L), and arm the track for recording. Press record in your DAW to begin.

Використання фантомного живлення

If you are using a condenser microphone, it requires +48V phantom power. Ensure the microphone is connected before activating phantom power. Press the ФАНТОМ power switch on the front panel. The corresponding LED will illuminate. Always disengage phantom power before disconnecting condenser microphones.

Підключення MIDI

The US-144MKII includes MIDI In and Out ports. Connect your MIDI keyboard, controller, or other MIDI devices to these ports. Your DAW software will recognize the US-144MKII as a MIDI interface, allowing you to send and receive MIDI data for controlling virtual instruments or external hardware.

Технічне обслуговування

• Прибирання: Використовуйте м’яку суху тканину для протирання зовнішньої частини пристрою. Не використовуйте абразивні засоби для чищення, віск або розчинники.
• Зберігання: When not in use for extended periods, disconnect the USB cable and store the unit in a clean, dry place away from extreme temperatures.
• Догляд за кабелем: Avoid bending or crimping USB and audio cables excessively. Store them neatly to prevent damage.

Усунення несправностей

• No Sound/Device Not Recognized:
  • Ensure the latest drivers are installed from the Tascam webсайт.
  • Verify the USB cable is securely connected to both the interface and the computer. Try a different USB port or cable.
  • Check your computer's sound settings and your DAW's audio preferences to ensure the US-144MKII is selected as the input/output device.
  • Restart your computer and the interface.
• Latency Issues (Delay in Monitoring):
  • Використовуйте MON MIX knob for zero-latency hardware monitoring.
  • In your DAW, reduce the buffer size in the audio settings. Lower buffer sizes reduce latency but require more CPU power.
  • Ensure your computer meets the minimum system requirements for your DAW and the interface.
• Noisy Sound/Interference:
  • Check all cable connections for security and integrity.
  • Забезпечте належне посиленняtaging; avoid setting input levels too high, which can cause clipping and distortion.
  • Try using a different USB port, preferably one directly on your computer's motherboard rather than a hub.
  • Keep the interface away from other electronic devices that might cause interference.
• Interface Disconnects on Mac Sleep:
  • This can be a known behavior with some Mac systems. Try adjusting your Mac's energy saver settings to prevent USB ports from sleeping.
  • If the issue persists, you may need to unplug and re-plug the USB cable, and re-select the interface in your DAW's preferences after your Mac wakes up.
• Проблеми з фантомним живленням:
  • Ensure the microphone is properly connected before engaging phantom power.
  • Verify the microphone itself is functional and requires +48V phantom power.

Технічні характеристики

Гарантія та підтримка

For warranty information, technical support, or service inquiries, please refer to the warranty card included with your product or visit the official Tascam webсайт. Там ви можете знайти детальні ресурси підтримки, відповіді на поширені запитання та контактну інформацію служби підтримки клієнтів.

Офіційний Tascam Webсайт: https://tascam.com/us/