1. Вступ
This manual provides essential information for the EBYTE E22P-868M30S and E22P-915M30S LoRa Spread Spectrum Wireless Modules. These modules are designed for high-performance wireless communication, utilizing SX1262/SX1268 chips and offering robust features for various applications.
Figure 1: E22P-868M30S LoRa Module
Figure 2: E22P-915M30S LoRa Module
2. Технічні характеристики
The E22P series modules are high-performance LoRa wireless modules with the following key specifications:
Загальні параметри
| Параметр | Значення | опис |
|---|---|---|
| Тип | Модуль | |
| RF чіп | SX1262 | |
| Частота кристалів | 32 МГц | |
| Потужність передачі | 30dBm (approx. 1W) | |
| Відстань зв'язку | Up to 12000m (with 5dBi antenna, 2m height) | |
| Інтерфейс зв'язку | SPI | |
| Швидкість повітря (біт/с) | 0.018k ~ 300k | |
| Постачання Voltage | 2.5V ~ 5.5V | |
| Чутливість прийому | -150 дБм | |
| Antenna Form | IPEX/Стamp отвір | |
| Розмір продукту | 38.5 × 24 мм | |
| Вага продукту | 4.9 ± 0.1 г. | |
Model-Specific Parameters
| Модель | Діапазон робочих частот | Емісійний струм |
|---|---|---|
| E22P-868M30S | 863.3 - 873.3 МГц | 610 мА |
| E22P-915M30S | 902 - 928 МГц | 640 мА |
Figure 3: E22P-868M30S Main Parameters
Figure 4: E22P-915M30S Main Parameters
Antenna Specifications (JKS Antenna)
| Параметр | Значення |
|---|---|
| Діапазон частот | 868 МГц / 915 МГц |
| посилення | 3.0dBi |
| Імпеданс | 50 Ом |
| Коефіцієнт стоячої хвилі | ≤ 1.5 |
| Інтерфейс | IPEX-1 (IPEX1 generation) |
Figure 5: E22P-868M30S with JKS Antenna Specifications
Figure 6: E22P-915M30S with JKS Antenna Specifications
3. Налаштування та встановлення
These modules are designed for integration into custom electronic projects. Proper handling and soldering techniques are essential for successful operation.
3.1 General Integration Guidelines
- Джерело живлення: Забезпечити подачу обtage is within the specified range of 2.5V to 5.5V. Stable power is crucial for reliable operation.
- Інтерфейс зв'язку: The module uses an SPI (Serial Peripheral Interface) for communication with a host microcontroller. Refer to the module's datasheet (not provided here, but typically available from the manufacturer) for detailed pinout and SPI protocol specifications.
- Підключення антени: Connect a suitable 868MHz or 915MHz antenna to the IPEX connector or stamp hole. Ensure the antenna impedance matches the module's 50 Ohm impedance.
- Екологічні міркування: The module is designed to operate in environments from -40°C to 85°C. However, avoid extreme temperature fluctuations and high humidity.
- Захист від ESD: The module includes ESD protection. However, always follow standard ESD precautions when handling electronic components.
3.2 Характеристики модуля
- Built-in RF front-end module, PA (Power Ampпідсилювач), LNA (низький рівень шуму Amplifier), SAW (Surface Acoustic Wave) filter, and ceramic filter for enhanced performance.
- High-precision active temperature-compensated crystal oscillator (32MHz) ensures stable frequency operation over a wide temperature range.
- Utilizes new SX1262/SX1268 chips for improved efficiency, longer distance, faster data rates, and smaller size compared to older generations.
Figure 7: Performance benefits of SX1262/SX1268 chips
Figure 8: Frequency stability comparison with high-precision crystal oscillator
4. Інструкція з експлуатації
Once integrated into your system, the module operates as a LoRa transceive device. Programming of the host microcontroller is required to control the module via its SPI interface.
4.1 Основна операція
- Ініціалізація: Configure the module's registers via SPI to set parameters such as operating frequency, spreading factor, bandwidth, and coding rate.
- Спосіб передавання: Load data into the module's transmit buffer and initiate transmission. The module will handle the LoRa modulation and RF transmission.
- Рецепція: Configure the module for reception. It will listen for incoming LoRa packets on the specified frequency and parameters. Received data can be read from the module's receive buffer via SPI.
- Управління живленням: Utilize the module's low-power modes (if supported by the SX1262/SX1268 chip and implemented in your firmware) to conserve energy in battery-powered applications.
For detailed programming and register configurations, refer to the SX1262/SX1268 datasheet and any available EBYTE programming guides or libraries.
5. Технічне обслуговування
These modules are designed for long-term reliability and generally require minimal maintenance. However, adhering to good practices can extend their lifespan and ensure optimal performance.
- Чистота: Keep the module free from dust, dirt, and moisture. Use a soft, dry brush or compressed air for cleaning if necessary.
- Екологічний контроль: Operate the module within its specified temperature and humidity ranges. Avoid exposure to corrosive substances.
- Цілісність з'єднання: Periodically check all connections, especially antenna connections, for secure fit and absence of damage.
- Оновлення прошивки: If EBYTE releases firmware updates for the module (typically applied via the host microcontroller), consider applying them to benefit from improvements or bug fixes.
6. Вирішення проблем
If you encounter issues with your LoRa module, consider the following troubleshooting steps:
- Немає зв'язку:
- Перевірте рівень живленняtagе та стабільність.
- Check SPI connections (MOSI, MISO, SCK, CS) and ensure they are correctly wired and enabled.
- Confirm the host microcontroller's SPI configuration (mode, clock speed).
- Ensure the module is correctly initialized in your firmware. - Поганий діапазон/якість сигналу:
- Check antenna connection and ensure it is securely attached and undamaged.
- Verify the antenna is appropriate for the module's operating frequency (868MHz or 915MHz).
- Ensure there are no obstructions between transmitting and receiving modules.
- Check for local RF interference.
- Confirm transmit power and receive sensitivity settings in firmware. - Перегрів модуля:
- Забезпечити об'єм постачанняtage не перевищує 5.5 В.
- Check the emission current against specifications (610mA for 868M30S, 640mA for 915M30S). Excessive current draw may indicate a fault or incorrect configuration. - Переривчаста робота:
- Check for loose connections or cold solder joints.
- Ensure the power supply is stable and free from noise.
- Реview your firmware for potential timing issues or race conditions.
7. Поради користувача
- Зовнішня антена: For optimal communication range, always use an external antenna with appropriate gain and ensure it is positioned away from other electronic components and metal objects.
- Фільтрація потужності: Consider adding additional power supply filtering (e.g., capacitors) close to the module's power pins to ensure a clean power source, especially in noisy environments.
- Software Libraries: Look for existing open-source LoRaWAN or LoRa libraries for your chosen microcontroller platform. These can significantly simplify development.
- Відповідність нормативним вимогам: Be aware of local regulations regarding RF power output and frequency usage in your region to ensure compliant operation.
8. Гарантія та підтримка
For any technical support, warranty claims, or inquiries regarding the EBYTE E22P-868M30S and E22P-915M30S LoRa Wireless Modules, please contact the seller, Rui Electronics Store, directly through the platform where the purchase was made. Ensure you provide your order details and a clear description of the issue to facilitate prompt assistance.
