WVCLTVJA (LM8-RR4D) Load Cell Indicator Weighing Controller User Manual

1. Вступ

This manual provides detailed instructions for the installation, operation, and maintenance of the WVCLTVJA (LM8-RR4D) Load Cell Indicator and Weighing Controller. This device is designed to accurately measure and display weight from 1 to 4 load cell inputs and provides 2 relay outputs for control applications. Please read this manual thoroughly before use to ensure proper functionality and safety.

2. Інформація про безпеку

• Електрична безпека: Ensure the power supply matches the device's requirements (AC 220V/110V). Disconnect power before making any wiring connections or performing maintenance.
• Кваліфікований персонал: Installation and wiring should only be performed by qualified personnel to prevent electric shock or damage to the device.
• Середовище: Do not expose the device to excessive moisture, dust, corrosive gases, or extreme temperatures. Operate within specified environmental conditions.
• Заземлення: Забезпечте належне заземлення, щоб запобігти небезпеці ураження електричним струмом.
• Load Cell Compatibility: Use load cells compatible with the indicator's input specifications.

3. Продукт закінчивсяview

3.1 Передня панель

малюнок 1: Front Panel of the LM8-RR4D Load Cell Indicator. It features a large red LED display for Process Value (PV) and a smaller green LED display for Set Value (SV). Indicators for 'LM' (Limit), 'g', 'AL1', 'AL2', 'AL3', 'T' (Tare), and 'Kg' are also present. Control buttons include 'SET', 'M' (Mode/Shift), 'Up', and 'Down'.

• PV дисплей: Large red LED display showing the current measured weight (Process Value).
• Дисплей SV: Smaller green LED display showing the set point or parameter value (Set Value).
• Індикатори: 'g' (grams), 'Kg' (kilograms), 'T' (Tare), 'AL1', 'AL2', 'AL3' (Alarm indicators), 'LM' (Limit).
• кнопки:
  • НАСТРОЙКА: Enters parameter setting mode or confirms settings.
  • M (Mode/Shift): Used to cycle through modes or shift digits during setting.
  • Вгору (▲): Збільшує значення або переміщується по меню.
  • Вниз (▼): Зменшує значення або переміщується по меню.

3.2 Rear Panel & Wiring Terminals

малюнок 2: Rear Panel of the LM8-RR4D Load Cell Indicator, displaying numbered screw terminals for power, load cell input, and relay outputs. The wiring diagram is also visible on the label.

The rear panel provides all necessary connections for power, load cells, and relay outputs. Refer to the wiring diagram printed on the device label for specific terminal assignments.

4. Налаштування та встановлення

4.1 Монтаж

The LM8-RR4D is designed for panel mounting. Ensure adequate space for ventilation and wiring connections. Secure the device firmly in the panel cutout.

4.2 Підключення проводів

Before making any connections, ensure the power supply is disconnected. Refer to the wiring diagram on the device label and Figure 2 for terminal identification.

1. Power Supply (AC 220V/110V): Connect the appropriate AC power supply to the designated terminals (e.g., 110V/220V, N, L). Ensure the voltage matches your local supply and the device's setting.
2. Load Cell Input:
   • Connect the load cell excitation voltage wires (EXC+, EXC-) to the corresponding terminals.
   • Connect the load cell signal wires (SIG+, SIG-) to the corresponding terminals.
   • The device supports 1 to 4 load cells. For multiple load cells, ensure they are wired in parallel correctly.
3. Relay Outputs (AL1, AL2):
   • Connect your external control devices (e.g., alarms, solenoids) to the AL1 and AL2 relay output terminals.
   • Each relay typically has Common (COM), Normally Open (NO), and Normally Closed (NC) contacts. Wire according to your application's requirements.
4. Communication (Optional, if available): If your model includes RS485 communication, connect the A and B lines to the respective terminals for data transmission.

Після виконання всіх підключень, перед подачею живлення, ще раз перевірте правильність та безпеку підключення проводки.

5. Інструкція з експлуатації

5.1 Увімкнення живлення

Once wired, apply power. The LED display will illuminate, showing the current weight (PV) and potentially a set value (SV).

5.2 Основна операція

• Zeroing/Tare: Pressing the 'M' button briefly may perform a tare function, setting the current weight to zero. Consult the full manual for specific tare procedures.
• Вибір одиниці: The 'g' and 'Kg' indicators suggest unit selection. This is typically done through parameter settings.

5.3 Parameter Setting and Calibration

The LM8-RR4D requires calibration to ensure accurate weight readings. This involves setting zero and span points using known weights.

1. Увійти в режим налаштування: Press and hold the 'SET' button for a few seconds to enter the parameter setting mode. The SV display will show a parameter code.
2. Параметри навігації: Use the 'Up' (▲) and 'Down' (▼) buttons to scroll through different parameter codes.
3. Змінити значення параметра: When the desired parameter code is displayed, press 'SET' again to view its current value. Use 'Up' (▲) and 'Down' (▼) to adjust the value. The 'M' button may be used to shift digits.
4. Зберегти та вийти: Press 'SET' to confirm the value. To exit the setting mode, press and hold 'SET' again, or the device may automatically exit after a period of inactivity.

Specific parameter codes and their functions (e.g., zero calibration, span calibration, decimal point, filter settings, alarm set points for AL1/AL2) are detailed in the comprehensive product manual.

6. Технічне обслуговування

• Прибирання: Clean the device exterior with a soft, dry cloth. Do not use abrasive cleaners or solvents. Ensure no liquids enter the device.
• Огляд: Periodically check wiring connections for looseness or damage. Ensure the mounting is secure.
• Повторне калібрування: If accuracy drifts or after significant environmental changes, recalibrate the device using known weights.
• Зберігання: If storing the device, do so in a dry, dust-free environment within the specified temperature range.

7. Вирішення проблем

Якщо проблема не зникає після спроби цих рішень, зверніться до служби підтримки клієнтів.

8. Технічні характеристики

9. Гарантія та підтримка

For warranty information and technical support, please refer to the documentation provided with your purchase or contact your vendor. Keep your purchase receipt as proof of purchase.