1. Важлива інформація з безпеки
Будь ласка, уважно прочитайте всі інструкції перед встановленням та використанням. Зберігайте цей посібник для подальшого використання.
- Джерело живлення: This LED strip operates on 12 В постійного струму. Connecting it to a higher voltage power source will damage the strip and may pose a fire hazard. Ensure your power supply is compatible and provides sufficient wattage for the length of the strip used. Power supply and controller are not included.
- Водонепроникність: Цей продукт має Рейтинг IP30, тобто це так не водонепроникний. Do not expose it to water, moisture, or high humidity. It is suitable for indoor use or protected outdoor environments where it will not come into contact with liquids.
- Різання: The LED strip can be cut to desired lengths only at designated cutting marks, typically indicated by a copper pad and a scissor icon. Cutting elsewhere will damage the circuit and render that section unusable.
- Установка: Ensure the installation surface is clean, dry, and smooth for proper adhesion. Avoid bending the strip sharply, as this can damage the internal circuitry.
- Електричні підключення: All electrical connections should be made securely to prevent short circuits or loose contacts. If you are unsure about wiring, consult a qualified electrician.
- Розсіювання тепла: While LED strips generate minimal heat, ensure adequate ventilation, especially when installed in enclosed spaces, to prolong product lifespan.
2. Продукт закінчивсяview
The TOPXCDZ GS1903 Pixel LED Strip is a 5-meter addressable light tape featuring 60 LEDs per meter. It utilizes 5050SMD RGB LEDs with an external GS1903 chipset, allowing for individual control of every 3 LEDs (20 ICs per meter). This enables dynamic full-color effects such as chasing, scanning, and various dream color patterns. The strip operates on 12V DC and comes with a white PCB, 6mm width, and an IP30 non-waterproof rating.
Вміст упаковки:
- 1 x 5-meter GS1903 Pixel LED Strip
Note: Power supply and LED controller are not included and must be purchased separately.
Зображення 2.1: Детальний опис view of the LED strip, highlighting the 5050SMD RGB LED chip, GS1903 IC (one IC controls three LEDs), safe resistor for stable voltage, and designated cutting points.
3. Технічні характеристики
| Особливість | Специфікація |
|---|---|
| Джерело світлодіодів | 5050SMD RGB External GS1903 chipset |
| Тип IC | GS1903 (WS2811 compatible) |
| Робочий вхід Voltage | 12 В постійного струму |
| Вихідна потужність | 0.2 Вт на світлодіод |
| Режим водіння | Постtage |
| Кількість світлодіодів | 60 LEDs/Meter (3 LEDs controlled by 1 IC) |
| Кількість ІС | 20 ICs/Meter |
| Пікселі | 20 Pixels/Meter |
| Шкала сірого | 256 |
| Колір | RGB (Full Color) |
| View Кут | 120° |
| Робоча температура | -20°C до 60°C |
| PCB Color | White PCB |
| Рейтинг водонепроникності | IP30 (неводонепроникний) |
| Ширина друкованої плати | 6 мм |
| Потужність (макс.) | 14 Вт/метр |
| Спосіб контролю | App (via compatible controller) |
Image 3.1: LED strip dimensions and layout, indicating 60 LEDs/meter, 12V DC input, 6mm PCB width, and approximate 50mm segment length.
4. Налаштування та встановлення
4.1 Контрольний список перед встановленням:
- Джерело живлення 12 В постійного струму: Ensure it provides sufficient current (Amps) for the total wattage of your LED strip. For a 5-meter strip at 14W/meter, you would need at least 70W (approx. 6A at 12V).
- Compatible LED Controller: An addressable LED controller (e.g., SP107E, SP110E, K-1000C, or similar WS2811/GS1903 compatible controller) is required to control the strip's effects.
- Електропроводка: Appropriate gauge wires for connecting the strip to the controller and power supply.
- Чиста поверхня: The installation surface should be clean, dry, and free of dust or grease.
4.2 Етапи встановлення:
- Плануйте свій макет: Determine the desired path for your LED strip. Measure and mark the installation area.
- Підготуйте поверхню: Clean the installation surface thoroughly. For optimal adhesion, use rubbing alcohol to remove any residues and let it dry completely.
- Cut the Strip (if necessary): If a shorter length is required, carefully cut the LED strip only at the designated cutting marks (copper pads with a scissor icon).
- Підключення до контролера: Connect the LED strip to your compatible addressable LED controller. The strip typically has four wires: 12V (positive), GND (negative), DI (Data Input), і DO (Data Output). Connect these to the corresponding terminals on your controller.
- Підключення джерела живлення: Connect the 12V DC power supply to your LED controller. Ensure correct polarity (positive to positive, negative to negative).
- Test Before Final Adhesion: Before peeling off the adhesive backing and permanently mounting the strip, connect all components and power them on to ensure the strip functions correctly.
- Монтування смужки: Once tested, peel off the protective backing from the adhesive tape on the back of the LED strip and carefully press the strip onto the prepared surface. Apply firm, even pressure along the entire length.
Image 4.1: Connection points on the LED strip (12V, DO, DI, GND).
5. Інструкція з експлуатації
The TOPXCDZ GS1903 Pixel LED Strip is an addressable LED product, meaning each segment of 3 LEDs can be controlled independently. To operate the strip and achieve various lighting effects, a compatible LED controller (not included) is required.
5.1 Using the LED Controller:
- Refer to the specific user manual provided with your LED controller for detailed instructions on its operation.
- Most controllers for GS1903/WS2811 strips offer control via a dedicated mobile application (App), remote control, or onboard buttons.
- Ensure your controller is set to the correct IC type (GS1903 or WS2811) and the correct number of pixels/LEDs to match your strip's configuration (20 pixels/meter, 60 LEDs/meter).
5.2 Common Functions (Controller Dependent):
- Вибір кольору: Choose from a wide spectrum of static colors.
- Динамічні режими: Access various pre-programmed effects such as chasing, scanning, fading, flashing, and other 'dream color' patterns.
- Регулювання яскравості: Збільште або зменшіть інтенсивність світла.
- Контроль швидкості: Налаштуйте швидкість динамічних світлових ефектів.
- Налаштування: Some advanced controllers allow for custom pattern creation and sequencing.
Зображення 5.1: Наприкладample of dynamic RGB lighting effects achievable with the LED strip.
Image 5.2: Further illustration of the diverse lighting patterns.
6. Технічне обслуговування
Proper maintenance ensures the longevity and optimal performance of your LED strip.
- Прибирання: Gently wipe the surface of the LED strip with a soft, dry, lint-free cloth to remove dust. Do not use abrasive cleaners, solvents, or excessive moisture.
- Перевірка підключення: Periodically inspect all electrical connections to ensure they are secure and free from corrosion. Loose connections can lead to flickering or intermittent operation.
- Фізичний огляд: Check the strip for any signs of physical damage, such as cracks, tears, or exposed wiring. If damage is found, discontinue use and replace the affected section or the entire strip.
- Умови навколишнього середовища: Ensure the strip remains within its specified operating temperature range (-20°C to 60°C) and is not exposed to moisture, as it is non-waterproof (IP30).
7. Вирішення проблем
If you encounter issues with your LED strip, refer to the following common problems and solutions:
| проблема | Можлива причина | Рішення |
|---|---|---|
| Світлодіодна стрічка не світиться. | Немає живлення, неправильна гучністьtage, loose connections, faulty controller, damaged strip. | Verify 12V DC power supply is connected and working. Check all wiring connections (12V, GND, DI). Ensure the controller is powered on and functioning. Test with a known good controller if possible. Inspect the strip for visible damage. |
| Incorrect colors or patterns. | Controller settings incorrect, data wire (DI) connected to wrong pin, faulty controller. | Check your LED controller's settings to ensure the correct IC type (GS1903/WS2811) and pixel count are selected. Verify the DI wire is connected to the data output of the controller. |
| Only a section of the strip is not working. | Damaged segment, improper cut, loose connection at a cut point. | Inspect the non-working section for physical damage. If the strip was cut, ensure the connections at the cut point are secure and properly soldered (if applicable). |
| LEDs are flickering or dim. | Insufficient power supply, loose connections, voltage drop over long runs, faulty controller. | Ensure your 12V DC power supply has enough wattage/current for the entire strip. Check all connections for tightness. For very long runs, consider injecting power at multiple points or using thicker gauge wires. |
| Strip gets excessively hot. | Переволtage, poor ventilation, short circuit. | Immediately disconnect power. Verify the power supply is 12V DC. Ensure the strip is not covered or installed in an enclosed space without airflow. Check for any visible short circuits. |
8. Гарантія та підтримка
This product is manufactured to high-quality standards. For any questions, technical assistance, or warranty claims, please contact the seller or manufacturer directly through your purchase platform. Please have your order number and product model (GS1903 Pixel LED Strip) ready when contacting support.