Rakstore ZB2L3 Battery Capacity Tester User Manual

1. Вступ

The Rakstore ZB2L3 Battery Capacity Tester is a versatile device designed to measure the capacity of various battery types, including 18650 Lithium batteries and Lead-Acid batteries. It functions as a discharge tester, allowing users to determine the actual capacity by discharging the battery through a load and measuring the discharged energy. This manual provides detailed instructions for the safe and effective use of the ZB2L3 tester.

2. Інформація про безпеку

• Always ensure correct polarity when connecting batteries to avoid damage to the tester and battery.
• Use appropriate discharge loads. Overloading the tester or using incorrect loads can cause overheating and damage.
• Не замикайте клеми акумулятора.
• Operate the device in a well-ventilated area, especially when discharging batteries, as they can generate heat.
• Тримайте пристрій подалі від вологи та екстремальних температур.
• Цей пристрій не є іграшкою. Зберігати в недоступному для дітей.

3. Особливості продукту

• Джерело живлення: DC4.5-6V via micro USB interface.
• Робочий струм: Less than 70mA.
• Розряд Voltage Діапазон: 1-15V with 0.01V resolution.
• Припинення Voltage Діапазон: 0.5-11.0В.
• Supported Discharge Current: Up to 3.000A with 0.001A resolution.
• томtage Помилка вимірювання: Less than 1% + 0.02V.
• Поточна помилка вимірювання: Less than 1.2% ± 0.002A.
• Діапазон ємності акумулятора: Up to 9999Ah (1Ah=1000mAh). Display adjusts decimal point for large values (e.g., X.XXX Ah, XX.XX Ah).
• Компактний розмір: Circuit board 50mm x 37mm, finished product 50mm x 37mm x 17mm (L x W x H, including copper foot height).

4. Вміст упаковки

• 1 x Rakstore ZB2L3 Battery Capacity Tester Unit
• (Note: Discharge resistors and battery holders are typically sold separately and are required for operation.)

5. Налаштування

Before operating the ZB2L3 tester, ensure all connections are made correctly.

Figure 1: ZB2L3 Battery Capacity Tester showing the micro USB power input, battery terminals, and load terminals.

1. Підключення до джерела живлення: Connect a DC 4.5-6V power source to the micro USB port on the tester. A standard phone charger or power bank can be used. The display should light up.
2. Підключення акумулятора: Connect the battery to be tested to the "BAT+" and "BAT-" terminals. Ensure correct polarity. The tester will display the current battery voltage.
3. Discharge Load Connection: Connect an appropriate discharge resistor (load) to the "LOAD+" and "LOAD-" terminals. The resistance value of the load will determine the discharge current. Ensure the load can handle the expected power dissipation.

Важливо: The discharge current should not exceed 3.000A. Calculate the required resistance using Ohm's Law (R = V/I) and Power Law (P = V*I or P = I²*R) to ensure the resistor can handle the power. For example, if testing a 3.7V battery at 1A, you need a 3.7 Ohm resistor capable of dissipating at least 3.7W.

6. Інструкція з експлуатації

Follow these steps to perform a battery capacity test:

Figure 2: ZB2L3 Battery Capacity Tester showing the 'OK', '+', and '-' buttons for operation.

1. Початковий дисплей: After connecting the power and battery, the tester will display the battery's current voltage.
2. Set Termination Voltage:
   • Press the "OK" button once. The display will show the current termination voltage (e.g., "U 3.00").
   • Use the "+" and "-" buttons to adjust the termination voltage. This is the voltage at which the discharge test will stop. For 18650 Lithium batteries, a common termination voltage is 3.0V. For Lead-Acid batteries, consult the battery's specifications.
   • Press "OK" again to confirm the setting and return to the main display.
3. Start Discharge Test:
   • With the battery and load connected, and the termination voltage set, press and hold the "OK" button for approximately 3 seconds.
   • The tester will begin discharging the battery through the connected load. The display will cycle through current voltage (V), discharge current (A), and accumulated capacity (Ah).
4. Monitor Test Progress: Observe the display. The voltage will gradually decrease, and the accumulated capacity will increase.
5. Test Completion: The test will automatically stop when the battery voltage reaches the set termination voltage. The display will then show the final accumulated capacity (Ah) and flash.
6. View Результати: After the test stops, you can press the "OK" button to cycle through the final voltage, current, and capacity readings.
7. Reset for New Test: To start a new test, disconnect the battery and load, then reconnect them, or simply press and hold the "OK" button again to clear the previous results and start a new cycle.

7. Технічне обслуговування

• Прибирання: Використовуйте м’яку суху тканину для очищення пристрою. Не використовуйте рідкі засоби для чищення або розчинники.
• Зберігання: Зберігайте тестер у прохолодному, сухому місці, подалі від прямих сонячних променів та екстремальних температур.
• Огляд: Periodically check the terminals and connections for any signs of wear or damage.

8. Вирішення проблем

9. Технічні характеристики

10. Гарантія та підтримка

This product is manufactured by Rakstore. For any technical support or warranty inquiries, please refer to the retailer where the product was purchased or visit the official Rakstore webсайт для контактної інформації.

Зберігайте підтвердження покупки для гарантійних претензій.