Okin 2 Button 5 Pin Recliner Hand Control with USB - Instruction Manual

вступ

This manual provides instructions for the installation, operation, and maintenance of your Okin 2 Button 5 Pin Lift Chair or Power Recliner Hand Control with USB.

This control unit is designed for use with compatible lift chairs and power recliners, offering convenient control over reclining functions and a built-in USB charging port.

Особливості продукту

• матеріал: Zinc alloy pane for durability.
• USB зарядка: 5V 2A output for mobile devices.
• Довжина кабелю: Approximately 125cm (4.1Ft) recliner switch cable.
• Сумісність: Works with Okin, Ashley Furniture, Dewert, Flexteel, Limoss, and many other power recliners using a 5-pin connection.

Okin 2 Button 5 Pin Recliner Hand Control with USB, showing the two control buttons and the USB charging port.

Налаштування та встановлення

This section details the steps for replacing or installing the hand control unit.

Необхідні інструменти: Small flat-head screwdriver or putty knife (for prying), zip ties (optional, for cable management).

Кроки встановлення:

1. Відключити живлення: Ensure the recliner is unplugged from the electrical outlet before beginning installation.
2. Видалити старий елемент керування: Carefully remove the existing hand control unit from its mounting location. This may involve gently prying it out of the armrest or side panel.
3. Від’єднайте кабель: Disconnect the 5-pin connector of the old control from the recliner's motor or control box.
4. Підключити новий елемент керування: Connect the new Okin 2 Button 5 Pin Hand Control's cable to the recliner's control box. Ensure the 5-pin connector is securely seated.
5. Маршрутний кабель: Route the cable neatly and secure it with zip ties if necessary to prevent snagging or damage.
6. Install Unit: Insert the new hand control unit into the mounting hole. Ensure it clicks into place or is securely fastened using the provided circlips.
7. Знову підключіть живлення: Reconnect the recliner to the electrical outlet.

Вибухнув view diagram illustrating the components of the recliner hand control and its installation into a wooden frame, showing the switch cover, lower cover, circlips, and studs.

Close-up of the 5-pin connector, which connects the hand control to the recliner's motor system.

Інструкція з експлуатації

The Okin 2 Button 5 Pin Hand Control provides simple operation for your power recliner.

Функція лежачи:

• Extend Footrest / Recline: Натисніть і утримуйте "ВГОРУ" button to extend the footrest and recline the chair.
• Retract Footrest / Upright: Натисніть і утримуйте "ВНИЗ" button to retract the footrest and return the chair to its upright position.
• Примітка: Some recliner models may require continuous pressure on the button for the full range of motion.

Порт заряджання USB:

• The integrated USB port (5V 2A) is designed for charging mobile devices. Connect your device's USB cable to the port.
• Ensure the recliner is connected to a power source for the USB port to function.

Технічне обслуговування

To ensure the longevity and proper function of your hand control unit:

• Прибирання: Keep the unit clean by wiping it with a soft, dry cloth. Avoid abrasive cleaners or solvents, which can damage the surface or internal components.
• Перевірка кабелю: Ensure cables are not pinched, twisted, or damaged. Regularly inspect the cable for any signs of wear, fraying, or cuts.
• Умови навколишнього середовища: Do not expose the unit to excessive moisture, direct sunlight, or extreme temperatures.

Усунення несправностей

Блок керування не відповідає:

1. Перевірка живлення: Verify that the recliner is properly plugged into a working power outlet.
2. Перевірка підключення: Ensure that all cable connections, especially the 5-pin connector to the recliner's motor, are secure and fully inserted.
3. Пошкодження кабелю: Inspect the control cable for any visible damage or cuts. A damaged cable may prevent proper function.
4. Motor/Power Supply: If the issue persists after checking connections and cable, the recliner's motor or power supply unit may need inspection by a qualified technician.

Порт USB не заряджається:

1. Recliner Power: Ensure the recliner is powered on and connected to an electrical outlet. The USB port requires power from the recliner's system.
2. Cable/Device Check: Try a different USB cable or device to rule out issues with the charging cable or the device being charged.
3. Заміна агрегату: If the USB port still does not function, the control unit may require replacement.

Технічні характеристики

Detailed dimensions of the Okin 2 Button 5 Pin Recliner Hand Control, showing measurements of 3.27 inches, 1.42 inches, and 3.9 inches.

Задня view of the control unit, displaying product identification labels including P/N JLDK-17, DC 24V 2A, USB 5V 2A, and manufacturer Okin Refined Electric Technology Co., Ltd.

Гарантія та підтримка

For warranty information or technical support regarding this Okin 2 Button 5 Pin Recliner Hand Control, please refer to the documentation provided with your original recliner or contact the manufacturer directly. Specific warranty terms for this replacement part may vary.