EPEVER Tracer4210AN

Інструкція з експлуатації контролера сонячного заряду EPEVER Tracer4210AN 40A MPPT

Model: Tracer4210AN | Brand: EPEVER

1. Вступ і даліview

The EPEVER Tracer4210AN is a 40A MPPT (Maximum Power Point Tracking) solar charge controller designed for 12V and 24V DC systems. It efficiently regulates power from solar panels to charge various battery types, including lead-acid (Sealed, AGM, GEL, Flooded) and lithium (LiFePO4, Li(NiCoMn)O2) batteries. This controller features an advanced MPPT control algorithm for high tracking and conversion efficiency, ensuring optimal energy harvest from your solar array. It includes multiple built-in protections for safe and stable operation, and an LCD screen for easy monitoring and parameter customization.

Фронт view of the EPEVER Tracer4210AN 40A MPPT Solar Charge Controller.

Малюнок 1.1: Спереду View of the EPEVER Tracer4210AN Controller.

Назад view of the EPEVER Tracer4210AN 40A MPPT Solar Charge Controller, showing the heat sink.

Малюнок 1.2: Задня частина View of the EPEVER Tracer4210AN Controller.

2. Інформація про безпеку

Before installing or operating the EPEVER Tracer4210AN solar charge controller, please read all instructions carefully. Improper installation or operation can lead to equipment damage, personal injury, or property damage. Always ensure proper ventilation around the controller. Do not expose the controller to water or excessive humidity. Disconnect all power sources before performing any maintenance or adjustments.

Important Connection Order: Always connect the battery first, then the load, and finally the solar panel. When disconnecting, reverse this order: disconnect the solar panel, then the load, and finally the battery.

3. Особливості продукту

  • Advanced MPPT control algorithm for tracking efficiency greater than 98% and peak conversion efficiency of 99.5%.
  • Automatic identification of 12V/24V DC system voltage.
  • Supports various battery types: Lead-acid (Sealed, AGM, GEL, Flooded) and Lithium (LiFePO4, Li(NiCoMn)O2, User-defined).
  • Built-in multiple protections: PV over-voltage, перенапруження батареїtage, over-temperature, over-charging, short-circuit, reverse polarity, and temperature compensation.
  • Informative LCD screen and two buttons for customizable parameters and display of working status.
  • 4-сtage battery charging (Bulk, Boost, Float, and Equalization).
  • Common negative grounded design.
EPEVER Tracer4210AN MPPT efficiency diagram showing 99.5% tracking efficiency and 98% charge conversion efficiency.

Figure 3.1: MPPT Tracking and Charge Conversion Efficiency.

EPEVER Tracer4210AN showing multiple protection features like PV over current, battery over voltage, short circuit, and reverse polarity.

Figure 3.2: Multiple Protection Features of the Controller.

4. Вміст упаковки

The package for your EPEVER Tracer4210AN solar charge controller typically includes:

  • EPEVER Tracer4210AN MPPT Solar Charge Controller
  • Посібник користувача
  • Сертифікат якості
  • Small green connector (for temperature sensor)

Відео 4.1: Розпакування та все іншеview of the EPEVER Tracer-AN Series MPPT Solar Charge Controller (demonstrated with a Tracer3210AN model), showing package contents and physical features.

5. Налаштування та встановлення

Follow these steps for proper installation. Always ensure correct polarity and secure connections to prevent damage.

  1. Підключіть батарею: Loosen the screws on the battery terminals of the controller. Connect the positive (+) and negative (-) battery cables to the corresponding terminals. Ensure the connection is secure. The controller will automatically detect the system voltage (12 В/24 В).
  2. Підключіть навантаження: Loosen the screws on the load terminals. Connect the positive (+) and negative (-) load cables to the corresponding terminals.
  3. Підключіть сонячну панель: Loosen the screws on the solar panel (PV) terminals. Connect the positive (+) and negative (-) solar panel cables to the corresponding terminals.
  4. Підключення датчика температури (додатково): Insert the remote temperature sensor into the designated port on the controller. This allows for accurate battery temperature compensation during charging.

Важливо: Always connect the battery first, then the load, and finally the solar panel. When disconnecting, reverse this order: disconnect the solar panel, then the load, and finally the battery.

Connection diagram for EPEVER Tracer4210AN showing solar panel, battery, and DC load connections.

Figure 5.1: Basic Connection Diagram for the Solar Charge Controller.

EPEVER Tracer4210AN showing supported battery types: Lithium, Sealed, Flooded, Gel, AGM.

Figure 5.2: Supported Battery Types for the Controller.

6. Інструкція з експлуатації

The controller features an LCD display and two buttons ("SELECT" and "ENTER") for monitoring system status and configuring parameters.

6.1 РК-дисплей та функції кнопок

The LCD displays various system parameters such as battery voltage, charging current, load current, and temperature. Use the "SELECT" button to browse through different display interfaces and the "ENTER" button to confirm selections or enter settings mode.

EPEVER Tracer4210AN LCD display showing PV voltage, об’єм батареїtagе, і стан завантаження.

Figure 6.1: LCD Display showing system parameters.

6.2 Встановлення типу батареї

Щоб встановити тип батареї:

  1. Press the "ENTER" button and hold for 5 seconds under the battery voltagелектронний інтерфейс.
  2. Press the "SELECT" button when the battery type interface is flashing to cycle through available battery types (SEL, GEL, FLD, LiFePO4, Li(NiCoMn)O2, USE).
  3. Натисніть кнопку «ENTER», щоб підтвердити вибраний тип батареї.
Diagram showing steps to set battery type on the EPEVER Tracer4210AN LCD.

Figure 6.2: Steps for Setting Battery Type via LCD.

6.3 Setting Load Working Mode

To set the load working mode:

  1. Press the "ENTER" button and hold for 5 seconds under the load mode interface.
  2. Press the "SELECT" button when the load mode interface is flashing to choose the desired mode.
  3. Press the "ENTER" button to confirm the load mode.

Увага: Setting Light ON/OFF, Test mode, and Manual mode via Timer1. Timer2 will be disabled and display "2n".

7. Технічне обслуговування

Regular maintenance ensures optimal performance and longevity of your solar charge controller. Perform the following checks periodically:

  • Очистіть контролер: Тримайте контролер чистим та без пилу та сміття. Використовуйте суху тканину для протирання поверхні.
  • Перевірте підключення: Periodically inspect all wiring connections (solar panel, battery, load) to ensure they are tight and free from corrosion. Loose connections can cause overheating and damage.
  • Огляньте на наявність пошкоджень: Check for any visible signs of damage to the controller, cables, or terminals.
  • Перевірка вентиляції: Ensure that the controller's heat sink and ventilation openings are not blocked to allow for proper heat dissipation.

8. Вирішення проблем

If you encounter issues with your EPEVER Tracer4210AN, refer to the following general troubleshooting tips. For detailed error codes and solutions, consult the full user manual provided with the product.

  • Без дисплея/живлення: Перевірте з'єднання акумулятора та переконайтеся, що акумулятор має достатній рівень зарядуtage. Verify all fuses in the system.
  • Без зарядки: Ensure solar panels are connected correctly and receiving sunlight. Check PV voltage and current on the LCD. Verify battery type settings.
  • Навантаження не працює: Check load connections and ensure the load is within the controller's rated current. Verify load working mode settings.
  • Переповtagе/Під-тtage Сигналізація: Перевірте об'єм батареїtage and ensure it is within the safe operating range for the selected battery type.

The controller has multiple built-in protections (PV over-voltage, перенапруження батареїtage, over-temperature, over-charging, short-circuit, reverse polarity) which may activate to protect the system. If a protection is triggered, the LCD may display an error code or indicator. Address the underlying cause before resetting or restarting the system.

9. Технічні характеристики

Below are the key technical specifications for the EPEVER Tracer4210AN 40A MPPT Solar Charge Controller.

EPEVER Tracer4210AN Specifications
ПараметрЗначення
МодельІндикатор4210AN
Іменна система Voltage12 / 24В Авто
Тип батареїLead-acid (Sealed/Gel/Flooded)/Lithium (LiFePO4/Li(NiCoMn)O2)/User
Вхід батареї Voltage Дальність8~32В
Номінальний струм заряду40А
Номінальний струм розряду40А
Номінальна потужність заряду520 Вт/12 В, 1040 Вт/24 В
Макс. Ефективність перетворення≥98.0%
Ефективність відстеження≥99.5%
Макс. PV Open Circuit Voltage100V (at min. operating temp), 92V (at 25°C ambient temp)
MPPT Voltage Дальність(Обсяг батареїtage +2В) ~ 72В
Вирівнювання Випtage (Flooded)14.8 В
Boost Voltage (Flooded)14.6 В
Float Voltage (Flooded)13.8 В
Низька гучністьtage Повторно підключіть випtage (Flooded)12.6 В
Низька гучністьtage Відключити томtage (Flooded)11.1 В
Самоспоживання≤12 мА
КорпусIP30
Інтерфейс зв'язкуRS485 (RJ45)
ЗаземленняЗагальний негатив
Діапазон робочих температур-25°C ~ +45°C (100% input and output)
Розміри (ДxШxВ)250x180x63mm (approx. 10.8"L x 7.6"W x 3.2"H)
Вага нетто1.65 кг
EPEVER Tracer4210AN dimensions: 10.83 inches length, 7.6 inches width, 3.2 inches height.

Figure 9.1: Physical Dimensions of the Controller.

10. Гарантія та підтримка

The EPEVER Tracer4210AN Solar Charge Controller comes with a 1-year warranty. For warranty claims or technical support, please contact your vendor or EPEVER customer service.

For advanced parameter settings and monitoring, optional accessories are available:

  • Дистанційний лічильник MT50
  • eBOX-WIFI/BLE-01 (for APP monitoring)
  • CC-USB-RS485-150U cable (for PC software)
  • Remote Temperature Sensor (RTS300R47K3.81A)
EPEVER logo.

Figure 10.1: EPEVER Brand Logo.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.