KUS EL0274 Waterproof Water Temperature Gauge Instruction Manual

вступ

This manual provides comprehensive instructions for the KUS EL0274 Waterproof Water Temperature Gauge. It is designed to display the temperature of a water tank when connected to compatible water temperature sensors. The gauge utilizes a moving-magnet principle for accurate and stable readings, featuring good endurance and anti-vibration capabilities.

Ключові особливості:

• Indicating Range: 40-120 ℃ (104-248 °F)
• Робочий випtage: 12V/24V (a resistor is included for 24V applications)
• Варіанти підсвічування: Red or Yellow
• Рівень захисту: IP67 (completely waterproof, anti-fogging function, works up to 1m underwater)
• матеріал: 316 Stainless steel bezel with curved glass
• Fixing Dimension: 52 мм (2 дюйма)

Вміст упаковки

Перевірте наявність усіх елементів в упаковці:

• 1x Water Temperature Gauge
• 1x Multi-plug Socket (Connector Cable)
• 1x Installation Instruction Sheet
• 1x Resistor (for 24V applications)

Інструкції з монтажу

Follow these steps for proper installation of the water temperature gauge:

1. Підготовка монтажного отвору: Cut a 52mm (2-1/16") diameter hole in the dashboard or desired mounting panel. Ensure a minimum clearance of 55mm (2-3/16") behind the panel for the gauge body.
2. Align Gauge: Remove the fixing ring. There is an alignment tab on the gauge body; place the gauge in the panel hole and mark the position of this tab to correctly align the gauge.
3. Secure Gauge: Insert the gauge through the panel from the front, fit and tighten the fixing ring from the rear.
4. Підключення проводів: Connect the wires according to the wiring diagram provided. Note that a resistor is required for 24V circuit operation.
5. Вибір підсвічування: Choose between red and yellow backlight by connecting the corresponding wire (Orange for Red, Yellow for Yellow) into port IV at the back of the gauge.
6. Voltmeter Note: If the gauge is a voltmeter, there are no black wire or resistors in the kit. This instruction applies specifically to the water temperature gauge.

Wiring Diagram and Connection Details

Refer to the following connection details for the multi-plug socket:

• Червоний дріт: +12V/24V (Power Supply)
• Помаранчевий дріт: Red Backlight (+)
• Жовтий дріт: Yellow Backlight (+)
• Синій провід: Земля (-)
• Чорний дріт: Сигнал датчика

Інструкція з експлуатації

Once properly installed and wired, the KUS Water Temperature Gauge will display the water temperature within its specified range of 40-120℃.

• Увімкнення: The gauge activates when power is supplied to the red wire (+12V/24V) and the blue wire is grounded.
• Індикація температури: The needle will indicate the current water temperature as measured by the connected sensor.
• Backlight Operation: The chosen backlight (red or yellow) will illuminate when its respective wire (orange for red, yellow for yellow) receives power.

Технічне обслуговування

The KUS Water Temperature Gauge is designed for durability and requires minimal maintenance. Due to its IP67 waterproof and anti-fogging features, it is built to withstand harsh environments.

• Прибирання: Очистіть поверхню калібру м’якою губкоюamp cloth. Avoid abrasive cleaners or solvents that could damage the glass or bezel.
• Огляд: Periodically check wiring connections for corrosion or looseness, especially in marine or high-vibration applications.
• Перевірка датчика: Ensure the water temperature sensor is clean and properly installed for accurate readings.

Усунення несправностей

If you encounter issues with your KUS Water Temperature Gauge, consider the following:

• Немає живлення/немає дисплея:
  • Check the power supply to the red wire (+12V/24V).
  • Verify the ground connection (blue wire).
  • Переконайтеся, що всі з’єднання надійні та не мають корозії.
• Неправильне значення температури:
  • Confirm the water temperature sensor is correctly installed and functioning.
  • Check the black sensor signal wire for proper connection.
  • Ensure the gauge is compatible with your specific water temperature sensor.
• Підсвічування не працює:
  • Verify power to the orange (red backlight) or yellow (yellow backlight) wire.
  • Ensure the correct backlight wire is connected to port IV.
• Gauge Fogging: While the gauge has anti-fogging properties, extreme temperature changes or prolonged exposure to high humidity might temporarily affect visibility. This should clear up under normal operating conditions.

If problems persist, consult a qualified technician or contact KUS customer support.

Технічні характеристики

Гарантія та підтримка

For warranty information, technical support, or service inquiries regarding your KUS EL0274 Water Temperature Gauge, please refer to the documentation provided at the time of purchase or contact the authorized KUS dealer or manufacturer directly. Keep your purchase receipt as proof of purchase for warranty claims.